NEC Neax2000 Ivs Isdn System Manual

ND -4 5857 ( E)  CHAPTER 4
SYSTEM  DATA  P R O GRAMM ING
X
* a *b
S TA RT
CM 12
C M 35
S TA RT
CM 35 

CHAPTER 4 ND-45857 (E)
Pag e 8 0
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.4 MEGACOM
® 800 Service Assignment
Refer to DID Addressing Assignment for programming instructions. 

ND-45857 (E) CHAPTER 4
Page 81
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.5 CPN to Network – Presentation Assignment
For providing the calling party number (CPN) to
the network, the data programming is shown be-
low.
• When Dial-In service is provided:
DESCRIPTION DATA
Assign an ISDN Subscriber’s Number of ISDN 
Number and ISDN Local Office Code Table 
Number to required station.• YY = 12
(1) X-XXXX (Station No.)
(2) X-XXXX (ISDN subscriber’s No.)
• YY = 13
(1) X-XXXX (Station No.)
(2) 00: ISDN Local...

CHAPTER 4 ND-45857 (E)
Pag e 8 2
Revision 3.0
SYSTEM DATA PROGRAMMING
• When BRI Terminals are used:
Note 1:The ISDN Number consists of the following numbers:
ISDN Number: XXXXXXXXXXXX  YYYY
This number must be in the indial range assigned by Telecom for the ISDN line.
For example:
National Destination Code for Dallas: 214
Local Code for a station: 518 - 5000
In this case, the ISDN Number is National Destination Code + Local Code = 214518 - 5000
That is:
ISDN Subscribers No. assigned byCM12 YY = 12 is...

ND-45857 (E) CHAPTER 4
Page 83
Revision 3.0
SYSTEM DATA PROGRAMMING
• When Dial-In service is not provided:
DESCRIPTION DATA
Specify the sending out of CPN (Calling Party 
Number).• YY = 25
(1) X-XXXX:  Station No. 
(2) 0/1  : To be sent out
Note 2
/Not to be sent out
Assign an ISDN subscriber’s Number of ISDN 
Number to each ISDN trunk. • YY = 19
(1) Trunk No. (000 – 255) assigned by CM07 
YY = 01
(2) XXXX: ISDN Subscriber’s No. 
Assign ISDN Local Office Code Table  Number 
to each ISDN trunk. • YY = 34...

CHAPTER 4 ND-45857 (E)
Pag e 8 4
Revision 3.0
SYSTEM DATA PROGRAMMING
Note 1:The ISDN Number consists of the following number.
ISDN Number: XXXXXXXXXXXX  YYYY
For example:
National Destination Code for Melbourne:  214
Local Code for the ISDN line: 518 - 5000
In this case, the ISDN Number is National Destination Code + Local Code = 214518 - 5000
That is:
ISDN Subscribers No. assigned by CM30 YY = 19 is 5000.
ISDN Local Office Code assigned by CM50 YY = 05 is 214518.
Note 2:The following facility control...

ND-45857 (E) CHAPTER 4
Page 85
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.6 CPN to Terminating User – Display Assignment
No programming is required.
3.3.7 Subaddress – Addressing Assignment
When the system has received a Called Party
Sub-address (Calling Station Number) from an
ISDN subscriber, the system makes the connec-
tion with the specified terminal.
DESCRIPTION DATA
Specify the terminating system for Called Party 
Subaddress.(1) 401  
(2) 0: Station Call
1  : Terminating System assigned by 
CM30 YY...

CHAPTER 4 ND-45857 (E)
Pag e 8 6
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.8 Subaddress – Present Assignment
When a station has dialed an ISDN subscriber’s
number, the station number is automatically sent
as a calling Party Subaddress.
3.3.9 Trunk Provisioning Service Selection AssignmentDESCRIPTION DATA
Provide the system with Calling party Subad-
dress to an ISDN network.(1) 400
(2) 0: To be sent out
DESCRIPTION DATA
Assign the Trunk Route to the Trunk No. as-
signed by CM07.• YY = 00 (Trunk Route...

ND-45857 (E) CHAPTER 4
Page 87
Revision 3.0
SYSTEM DATA PROGRAMMING
3.3.10 Automated Attendant Assignment
DESCRIPTION DATA
Assign the Trunk Route. • YY = 00
(1) Trunk No. (000 – 255)
(2) Trunk Route (00 – 63)
Assign the Trunk Tenant. • YY = 01
(1) Trunk No. (000 – 255)
(2) Trunk Tenant (00 – 63)
If no data is set, the default setting is 01.
Assign the data for Automated Attendant to re-
quired trunks.• YY = 02 (Terminating System in Day 
mode)
• YY = 03 (Terminating System in Night 
mode)
(1) Trunk No....

CHAPTER 4 ND-45857 (E)
Pag e 8 8
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
• YY = 32 (Handling of timed-out
Automated Attendant in day mode)
• YY = 37 (Handling of time-out Automated 
Attendant in night mode)
(1) Trunk No. (000 – 255)
(2) 00: C.O. Line Release
01: Forwarded to TAS
03: Forwarded to ATTCON
04: Forwarded to DIT Station
06: DT Connection for redial
15   : C.O. Line Release
• YY = 33 (In case YY = 30, 31 is set to data 
08, if all DTMF Receivers are busy.)
(1) Trunk No. (000 –...