NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Page 109
Revision 3.0
SYSTEM DATA PROGRAMMING
3.5 Basic Data Assignment for ISDN Terminal
3.5.1 ILC Assignment
DESCRIPTION DATA
Assign an ISDN Circuit Station Number to the 
required LEN.(1) LEN (0000-0511)
(2) EFX-EFXXXX: ISDN Circuit Station No.
Assign a Tenant No. to each ISDN Circuit Sta-
tion Number.• YY=04
(1) X-XXXX (ISDN Circuit Station No.)
(2) 00-63 (Tenant No.)
If no data is set, the default data is 01.
Assign a Trunk Restriction Class to each ISDN 
Circuit Station...

CHAPTER 4 ND-45857 (E)
Pag e 1 10
Revision 3.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the facility control of CPN
(Calling Party Number).• YY=25
(1) X-XXXX: ISDN Circuit Station No.
(2) 0/1 : To be provided/Not to be provided
Assign the digit number of ISDN Circuit Sta-
tion Number.•Y=0-3
(1) X-XXXX: ISDN Circuit Station No.
(2) 801: 1 digit 
802: 2 digits 
803: 3 digits 
804: 4 digits
Specify whether the subaddress is sent to an 
ISDN network when making a call from ISDN 
Terminal, if...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 111
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.5.2 ICH Assignment
DESCRIPTION DATA
Assign slot number to each ICH card (PN-
SC02/SC03). The slot number to be assigned 
must coincide with the value set by the SENS 
switch on the ICH card.(1) Slot No. (04-15)
(2) 13: ICH card
Assign the ICH Number to the Slot Number of 
ICH assigned by CM05.• YY=09
(1) ICH No. (00-11)
(2) XX
 
*a
*a: Slot No. assigned by CM05
Assign the ISDN Circuit Station Number to the...

CHAPTER 4 ND-45857 (E)
Pag e 1 12
Revision 3.0
SYSTEM DATA PROGRAMMING
3.6 Service Data Assignment for ISDN Terminal
3.6.1 Point to Point Connection Assignment
MDF
ISDN Terminal/TA
Max. 1965 ft. (600 m)
ILCPBX 

ND-45857 (E) CHAPTER 4
Addendum-001 Page 113
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the point to point connection as the Lay-
er 2 data link.
Note:When Point-to-Point Connection is select-
ed, the PBX will address the BRI Terminal
with channel select (B1/B2) message.
Some BRI Terminals cannot answer the
call with this type of 
signaling. Some of the BRI Terminals re-
quire a Calling Party Number sent from
the PBX. In this case, use Point-to-Multi-
point for CM AC01 and...

CHAPTER 4 ND-45857 (E)
Pag e 1 14
Revision 3.0
SYSTEM DATA PROGRAMMING
3.6.2 Point to Multipoints Connection Assignment
DESCRIPTION DATA
Assign the point to multipoints connection as 
the Layer 2 data link.• YY=01
(1) XX
 X
*a *b
*a: ICH No. (00-11)
*b: ISDN Circuit No. of ICH card (0-7)
(2) 1 : Point to Multipoints Connection
Specify the passive bus. • YY=03
(1) XX
 X 
*a *b
*a: ICH No. (00-11)
*b: ISDN Circuit No. of ICH card (0-7)
(2) 0: Extended Passive Bus 
1 : Short Distance Passive Bus
400407...

ND-45857 (E) CHAPTER 4
Page 115
Revision 3.0
SYSTEM DATA PROGRAMMING
BRI Programming Example:
The following is an example of common BRI Station Programming.
DESCRIPTION DATA
Assign an ISDN Terminal Multipoints Station 
Number to the ISDN Circuit Station Number.
The numbers assigned in this command are sta-
tion numbers that are to be programmed in the 
BRI terminal. CM 12 YY=12 will use the sta-
tion assignments from CM 10.(1) XXXX  X 
*a *b
*a: ISDN Circuit Station No. assigned 
by CM10
*b: ISDN...

CHAPTER 4 ND-45857 (E)
Page 115-1 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.6.3 National ISDN 1 BRI Terminal Assignment
DESCRIPTION DATA
Assign the point to multipoints connection as 
the Layer 2 data link.• YY=01
(1) XX
 X
*a *b
*a: ICH No. (00-11)
*b: ISDN Circuit No. of ICH card (0-7)
(2) 1 : Point to Multipoints Connection
Specify the passive bus.
Assign protocol as National ISDN 1.• YY=03
(1) XX
 X 
*a *b
*a: ICH No. (00-11)
*b: ISDN Circuit No. of ICH card (0-7)
(2)
•
(1)...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 115-2
AUGUST, 1998 Revision 3.1
This page is for your notes. 

CHAPTER 4  ND -4 5857 ( E)
S YST EM  DATA P RO G RA MMING
ISDN
IS DN  Term inal
I L C
P BX
C M 30
A
CM 35