NEC Neax2000 Ivs Isdn System Manual

ND-45857 (E) CHAPTER 4
Addendum-001 Page 127
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.8 Event Based CCIS Programming Example
3.9 Numbering Plan Programming in PBX A:
Station numbers in PBX A are 2000~2999.
Station numbers in PBX B are 3000~3999.
Digit conversion must be done for 6868~6871.
DESCRIPTION DATA
Access code for trunk route 10.
Access code for trunk route 11.• YY=0~3
2 >  804
3 >  A29
68 > 804
80 > 110
81 > 111
T
E
L
C
O D100 Rt. 10       (972) 555-6868
D101 Rt. 10       (972)...

CHAPTER 4 ND-45857 (E)
Page 128 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.9.1 Telco BRI Trunk Programming
BRI Trunks in PBX A are (Example for using BRTA cards):
Circuit 1: B1  (972) 555-6868
B2   (972) 555-6869
Circuit 2: B1  (972) 555-6870
B2  (972) 555-6871
Note:Sense Wheel on BRI cards are set to 04 and 05 respectively.
DESCRIPTION DATA
Assign BRI cards. 04 > 10
05 > 10
Set protocol as NI-1. • YY=06
04 > 27
05 > 27
Assign trunks to BRI. • YY=02
0400 > D100
0401 > D101
0500 >...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 129
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Area Code + Local Office Code • YY=05
00 > 972555
Last 4 digits of telephone no. + 4 digit SPID • YY=30
040 > 68680101
041 > 68690101
050 > 68700101
051 > 68710101
Set as ISDN trunk route.
Answer signal arrives.
Incoming connection signaling.
Hooking signal sending to outside not 
provided.
Enable digit conversion.
Disable trunk queuing outgoing.
Assign as BRI trunk route.•
•
•
•
•
•
•YY=00
10...

CHAPTER 4 ND-45857 (E)
Page 130 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
BRI Trunks in PBX B are:
Circuit 1: B1  (214) 555-6204
B2   (214) 555-6205
Circuit 2: B1  (214) 555-6206
B2  (214) 555-6207
Note:You must have this information prior to programming E-CCIS.
• Home-Side Trunk Programming
DESCRIPTION DATA
Assign Home-Side trunks to even numbered 
addresses.• YY=05
3200 > D030
3202 > D031
3204 > D032
3206 > D033
Assign trunks to trunk routes. • YY=00
030 > 30
031 > 30
032 > 30
033...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 131
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign CCH Channel No.
Assign as E-CCIS route.•
•YY=90
30 > 0
31 > 0
YYY=135
30 > 0
31 > 0
Assign CIC no. • YY=35
030 > 001
031 > 002
032 > 003CM35
CM30
A
END 

CHAPTER 4 ND-45857 (E)
Page 132 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
• Mate-Side Trunk Programming
DESCRIPTION DATA
Assign Mate-Side trunks to odd numbered 
addresses.• YY=05
3201 > D040
3203 > D041
3205 > D042
3207 > D043
Assign trunks to trunk routes.
Assign last 4 digits of telephone number in 
PBX B.•
•YY=00
040 > 40
041 > 41
042 > 42
043 > 43
YY=19 
040 > 6204
041 > 6205
042 > 6206
043 > 6207
Assign as Tie Line routes.
Assign abbreviated codes to terminate call to 
PBX B....

ND-45857 (E) CHAPTER 4
Addendum-001 Page 133
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.9.2 Program Termination for Incoming E-CCIS Calls
3.9.3 Program Access Code/Terminating Number Assignment for Outgoing E-CCIS Calls
3.9.4 Program Release Timer for Virtual Tie Lines (Home-Side & Mate-Side Trunks)DESCRIPTION DATA
Convert received digits to Mate-Side trunks. • Y=0 & Y=1
6868 > B040
6869 > B041
6870 > B042
6871 > B043
DESCRIPTION DATA
Allocate memory to store the terminating num-
bers of PBX B....

CHAPTER 4 ND-45857 (E)
Page 134 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3.9.5 CCH Data Assignment:
Sense Wheel for PN-SC00 is set to 06.
Originating Point Code for PBX A is 00001.
DESCRIPTION DATA
Assign CCH card.
• 06 > 11
Assign CCH channel no. to CCH card.
•YY=07
0 > 06
Provide the PBX with CCIS.
•53 > 0
Assign trunk to be used as CCH channel.
Assign Originating Point Code.
Assign Destination Point Code.
Assign ACM Signal Waiting Timer.
 E-CCIS for the CCH channel.•
•
•
•
•YY=00...

ND-45857 (E) CHAPTER 4
Addendum-001 Page 135
AUGUST, 1998 Revision 3.1
SYSTEM DATA PROGRAMMING
3.10 Numbering Plan Programming in PBX B:
Station numbers in PBX A are 2000~2999.
Station numbers in PBX B are 3000~3999.
Digit conversion must be done for 6204~6207.
DESCRIPTION DATA
Access code for trunk route 10.
Access code for trunk route 11.• YY=0~3
2 > A29
3 >  804
62 > 804
80 > 110
81 > 111
T
E
L
C
OD1 00  Rt.  10        (9 72 ) 5 55 -62 0 4
D101 Rt. 10       (972) 555-6205
D1 02  Rt.  10        (9 72 )...

CHAPTER 4 ND-45857 (E)
Page 136 Addendum-001
Revision 3.1 AUGUST, 1998
SYSTEM DATA PROGRAMMING
3 . 1 0 . 1 Te l c o  B R I  Tr u n k  P r o g r a m m i n g
BRI Trunks in PBX B are (Example for using BRTA cards):
Circuit 1: B1  (972) 555-6204
B2   (972) 555-6205
Circuit 2: B1  (972) 555-6206
B2  (972) 555-6207
Note:Sense Wheel on BRI cards are set to 04 and 05 respectively.
DESCRIPTION DATA
Assign BRI cards. 04 > 10
05 > 10
Set protocol as NI-1. • YY=06
04 > 27
05 > 27
Assign trunks to BRI. • YY=02
0400 >...