NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Pag e 3 68
Revision 2.0
CMF8
COMMAND CODE
TITLE:
SPECIAL COMMANDS
F8
4. DATA TABLE:
Note 1:The ID code received from the Interactive Voice Response (IVR) unit must be entered.
Note 2:The Special ID Code can be entered when the ID code is not provided due to trouble with the IVR
unit. The Special ID code is effective for 3 days (4320 minutes). If the exact ID code is not entered
within 3 days of entering the Special ID Code, you will be restricted for MAT/CAT operation.
1....

ND-45669 (E) CHAPTER 3
Pag e 3 69
Revision 2.0
CMD000
COMMAND CODE
TITLE:
SYSTEM FEATURES (1)
D000
4. DATA TABLE:
1. FUNCTION:
This command is used to assign SMDR and PMS functions.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
1ST DATA
2ND DATA
DATA FUNCTION
2 Designation of the language in which the messages are to be print-
ed out. 0 : Japanese
1 : English
11 By Check-In operation (   + Station No. +  ), check-
in time information has overflowed.0 : Not available
1 : Available
41 Action...

CHAPTER 3 ND-45669 (E)
Page 370 Addendum-001
Revision 2.1 AUGUST, 1998
CMD000
COMMAND CODE
TITLE:
SYSTEM FEATURES (1)
D000
: Initial Data
1ST DATA
2ND DATA
DATA FUNCTION
72 The Authorization Code is printed out. 0 : No
1 : Yes
76 Sending call information for tandem calls through CCIS 0 : Not sent
1:To send
77 Sending of detail information of tandem calls to SMDR terminal, 
which is set to “4” by CMD001-80/100/1200:Not sent
1:To send
78 Sending of detail information of tandem calls to SMDR terminal,...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 371
AUGUST, 1998 Revision 2.1
CMD000
COMMAND CODE
TITLE:
SYSTEM FEATURES (1)
D000
138 MCI/Printer for No. 3 Port
Note:No. 3 port on the PN-AP00 card can be only connected
to the VMS or printer which the RTS signal from the PN-
AP00 card is not needed.0:Not provided
1:To provide
140 Send a Violation Code Message when PBX receives an illegal 
message from PMS0:Not sent
1:To send
141 Send Violation Code message when PBX receives an undefined 
FTC message from...

CHAPTER 3 ND-45669 (E)
Pag e 3 72
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
4. DATA TABLE:
1. FUNCTION:
This command is used to assign various SMDR and PMS functions, and the interface conditions for the
SMDR terminal, printer and PMS.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
DATA1ST DATA
2ND DATA
FUNCTION
1 Method of charging a transferred call
• In the following are shown the stations to which call charging 
is to be made in the case of various transfer...

ND-45669 (E) CHAPTER 3
Pag e 3 73
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
4 Printout function of Check-In time and Checkout time, when the 
Checkout is set from a Front Desk Instrument.0 : Not available
1 : Available
5 Clearing of Check-In and setting of Room Cutoff service are exe-
cuted.0 : Not available
1 : Available
6 Designation of the number of line feeds after printing. 0 : No line feed
1 : 1 line feed
10 : 10 line feeds
11 Printout function of Room Status Information,...

CHAPTER 3 ND-45669 (E)
Pag e 3 74
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
23 Parity for No. 0 PortNote0:No parity
1:Even parity
2:Odd parity
24 Data Speed for No. 1 PortNote0:Not used
1 : 300 bps
2 : 1200 bps
3 : 2400 bps
4 : 4800 bps
5 : 9600 bps
25 Stop Bit Length for No. 1 PortNote0 : 1 bit
1 : 1.5 bits
2 : 2 bits
26 Data Length for No. 1 PortNote0 : 7 bits
1 : 8 bits
27 Parity for No. 1 PortNote0:No parity
1:Even parity
2:Odd parity
28 Data Speed for No. 2 PortNote0:Not used...

ND-45669 (E) CHAPTER 3
Pag e 3 75
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
32 Data Speed for No. 3 PortNote0:Not used
1 : 300 bps
2 : 1200 bps
3 : 2400 bps
4 : 4800 bps
5 : 9600 bps
33 Stop Bit for No. 3 PortNote0
: 1 bit
1 : 1.5 bits
2 : 2 bits
34 Data Length for No. 3 PortNote0 : 7 bits
1 : 8 bits
35 Parity for No. 3 PortNote0:No parity
1:Even parity
2:Odd parity
36 Message format which is sent to VMS with MCI 0 : Conventional (without ANI)
1 : Expanded (with ANI)
39 Expansion...

CHAPTER 3 ND-45669 (E)
Pag e 3 76
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
81 Priority for data processing on No. 0 PortNote0:1st
1:2nd
82 Message format on No. 0 Port Note
(when 2nd data of CMD001-80 is set to 4)0 : No data is sent.
3 : SMDR (NEAX2400 IMS format)
4 : SMDR (NEAX1400 IMS format)
6 : PMS (IMS format)
Number of characters per line to be printed out on Note
No. 0 port (when 2nd data of CMD001-80 is set to 16/17)0:Not used
2 : 80 characters
83 Number of lines per page...

ND-45669 (E) CHAPTER 3
Pag e 3 77
Revision 2.0
CMD001
COMMAND CODE
TITLE:
SYSTEM FEATURES (2)
D001
PORT 
No.FUNCTION
(PROVIDED TERMINAL)CALL INFORMATION 
SENT TO TERMINALDATA SETTINGS
1 SMDR C.O. Outgoing Calls 
Tie Line Outgoing CallsCMD001 -80 : 5
CMD016 -XX17 : 1
-XX22 : 1
0 PMS C.O. Outgoing Calls CMD001 -100 : 4
CMD016 -XX16 : 1
PORT 
No.FUNCTION
(PROVIDED TERMINAL)CALL INFORMATION 
SENT TO TERMINALDATA SETTINGS
0 SMDR C.O. Outgoing Calls  CMD001 -80 : 4
CMD016 -XX16 : 1
1 SMDR Tie Line Outgoing...