NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Pag e 1 54
Revision 2.0
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
04
(DDIT)Direct–In Termination in Day 
ModeX
XXXXStation Number for Direct–In Termi-
nation in Day ModeCM10, 11
CXX Abbreviated Code of System Speed 
Dialing for DIT–Outside (XX=00–31)CM71–66
CM35 YY=40
EBXXX Digital Announcement Trunk Circuit 
Number
(XXX=000–127)CM10, CM15
YY=33 CM20–
A00, A01, A02
CM49 YY=03000
05
(NDIT)Direct–In Termination in Night 
ModeX
XXXXStation Number for Direct–In Termi-
nation in Night...

ND -4 5669 ( E)  CHAPTER 3
CM 30
MAT
: In it ia l D ata
~
~
~~
~~
~ 

CHAPTER 3 ND-45669 (E)
Page 156 Addendum-002
Revision 2.2 JANUARY, 1999
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
28
(PAGA)Paging Answer Zone/Kind of 
PagingXX
CM20 – 070
CM20 – 079
CM44 – 02XX
Paging Answer Zone
0: Paging Answer Zone 0
9: Paging Answer Zone 9
Kind of Paging
0: Speaker Paging, no answer
1: Radio Paging, no answer
2: Speaker Paging, non-delay answer
3: Radio Paging, non-delay answer
4: Speaker Paging, non-delay and...

ND-45669 (E) CHAPTER 3
Addendum-002 Page 156-1
JANUARY, 1999 Revision 2.2
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
: Initial Data
YY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
31
(NRAD)Handling of busy/not available/
Automated Attendant/ Direct 
Inward System Access (DISA) 
in night mode.
Note:For DISA, this data is
effective only for a
station call.00
15 Same as YY=30 CM41
(Y=0 No. 34)
CM45
~ 

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 156-2 Addendum-002
Revision 2.2 JANUARY, 1999
This page is for your notes. 

ND-45669 (E) CHAPTER 3
Pag e 1 57
Revision 2.0
CM30
COMMAND CODE
TITLE:
TRUNK DATA
30
MAT
Note 1:When data 02, 03, 11 or 20 is assigned, the data for YY=18 should be set to 0.
Note 2:For DIDs and Tie Lines, YY = 02 and YY = 03 should be set to 31.
Note 3:For individual trunk access, it is necessary to assign the Trunk ID code in YY=19. The codes assigned
are the Trunk ID codes to be displayed on the ATTCON or Multiline Terminal.
32
(RATO)Handling of timed–out
Automated Attendant Call in 
Day mode.00
01...

CHAPTER 3 ND-45669 (E)
Pag e 1 58
Revision 2.0
CM31
COMMAND CODE
TITLE:
SYSTEM ATTRIBUTE DATA
31
MAT
4. DATA TABLE:
1. FUNCTION:
This command is used to assign the system attribute data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
Y1S T DATA 2ND DATA
DATA MEANING DATA MEANING
1 0 MF PAD Control to incoming signal 0
1
2
3
4
7–8 dBm
–10 dBm
–11.5 dBm
–9.13 dBm
Not used
1 Sensitivity Level of MF Receiver 00
14
15–21 dBm
–35 dBm
–36 dBm
(–1 dBm increments)
2 Number of received digits of...

ND-45669  (E)   CHAPTER 3
CM 31
MAT
20
 R ECE IV ER
0  No. 0 –3  as S ender
~
~~
I N IT IA L
~
~
I N IT IA L~
~ 

CHAPTER 3 ND-45669 (E)
Page 160 Addendum-002
Revision 2.2 JANUARY, 1999
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
1. FUNCTION:
This command assigns trunk route characteristics. A trunk route is a group of trunks with common char-
acteristics used for a common purpose.
2. PRECAUTION:
(1) The following table shows the value of the Central Office Trunk (COT/DID) PAD or Tie Line
Trunk (ODT/DTI) PAD assigned by YY=19, Data 4 – 7. (T:Transmitter PAD [dB], R:Receiver PAD
[dB])
+: Gain
-: Loss
CONNECTION...

ND-45669 (E) CHAPTER 3
Pag e 1 61
Revision 2.0
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
(2) When assigning a Tie Line, the data in YY = 09 (Incoming Call Signaling System) should be simi-
lar to that of YY = 20 (Sender Starting Condition). The following table shows the assignment of the
Sender Starting Condition in relation to the Incoming Call Signaling System.
Note:( ) indicates the data to be assigned.
(3) This command is included in MAT mode menu “B2” (Trunk Route data [COM01]).
3. ASSIGNMENT...