NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Page 172 Addendum-001
Revision 2.1 AUGUST, 1998
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
: Initial Data
YY/YYY SETTING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
87 Distinctive Ringing by detect-
ing the ringing signal from the 
Main PBX (or Centrex).0
1 To provide
Not provided
Note 1:When this function is utilized,
be sure to set Trunk Line 
Appearance as the terminat-
ing method (CM30 YY = 02,
03, set for 02).
Note 2:Tone Ringer is selected by
CM35 YY = 34; lamp...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 173
AUGUST, 1998 Revision 2.1
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
97 Assignment of route-class 
data in CCIS Route to Route 
RestrictionXX
Assignment data is the same as CM12 
YY=01
98 Designated seizure of trunks 
for Private Lines0
1 Allow
RestrictedCM12
YY=16
CM42-08
100 Assignment of Terminating 
Impedance for C.O. line00
01
02
14600 ohm (for regular/long line)
Balanced Network Imp.: complex
900 ohm
 Balanced Network Imp.: complex
600 ohm (for...

CHAPTER 3 ND-45669 (E)
Page 174 Addendum-001
Revision 2.1 AUGUST, 1998
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
135 Kind of trunk route for voice 
channel and common signal-
ing channel0
1 Event Based CCIS Route
Other Trunk Route
138 Sending of received ANI
information from network to 
VMS with MCI0
1 To send
Not sent
139 Roaming Service assignment 
for Virtual COT route0
1 Available
Not availableCM30
YY=00
140 Roaming Service 0
1 Available
Not available
141 Pursuit function after roaming 
PS0
1...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 174-1
AUGUST, 1998 Revision 2.1
CM35
COMMAND CODE
TITLE:
TRUNK ROUTE DATA
35
MAT
Note 1:In case of CM35 YY = 76, Data = 15, not specified (release the sender by time out or by answer
signal from the called distant office). 
In case of CM35 YY = 76, Data = 00 – 04, specified by the dialed digits assigned by CM85.
Note 2:STN means the calling party’s station number, and this number is sent automatically by CM30 –
28, Data = x6.
Note 3:LED indication for an internal...

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 174-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 

ND-45669 (E) CHAPTER 3
Pag e 1 75
Revision 2.0
CM36
COMMAND CODE
TITLE:
RESTRICTION DATA FOR TANDEM CONNECTION
36
4. DATA TABLE:
Note:The 2-digit Incoming Trunk Route number and the 2-digit Outgoing Trunk Route number are entered as a
concatenated 4-digit number. For example, the value “1824” would represent Incoming Trunk Route “18”
and Outgoing Trunk Route 24.
1. FUNCTION:
This command is used to define restriction data for tandem connection within a system, for each combi-
nation of an incoming trunk...

CHAPTER 3 ND-45669 (E)
Pag e 1 76
Revision 2.0
CM38
COMMAND CODE
TITLE:
AMP TRUNK
38
4. DATA TABLE:
1. FUNCTION:
This command is used to define the AMP Trunk controlled data.
2. PRECAUTION:
None
3. ASSIGNMENT PROCEDURE:
: Initial Data
YYINCOMING/OUTGOING TRUNK 
ROUTE NO.
AMP PATTERN NO.SETTING DATA
RELATED
COMMAND
DATA MEANING
00 00
14
15AMP Pattern Number 00
AMP Pattern Number 14
Not use the AMP Trunk
01 AMP Pattern Number 00
AMP Pattern Number 14Assignment of gain value
Fixed Gain
0 : 12dB
1 : 8dB
2 :...

ND-45669 (E) CHAPTER 3
Pag e 1 77
Revision 2.0
CM38
COMMAND CODE
TITLE:
AMP TRUNK
38
Note:CM38 YY=07 setting data 0 is effective except ISDN and CCIS lines.
03 AMP Pattern Number 00
AMP Pattern Number 140
1Echo Canceller Gain Controller
ON
OFF
04 AMP Pattern Number 00
AMP Pattern Number 140
1Mode Selection of Tone Disabler
G164
G165
05 AMP Pattern Number 00
AMP Pattern Number 140
1Detect Time of Tone Disabler
0 sec.
2 sec.
06 AMP Pattern Number 00
AMP Pattern Number 140
1Channel to be connected
Incoming...

CHAPTER 3 ND-45669 (E)
Pag e 1 78
Revision 2.0
CM40
COMMAND CODE
TITLE:
FUNCTION OF RS-232C INTERFACE CIRCUIT
40
1. FUNCTION:
This command is used to assign the function of the RS-232C interface circuits, mounted on the MP card.
The MP card has two RS-232C interface circuits, which are used for the following purposes:
(1) PN-CP00/PN-CP00-B
(2) PN-CP03
(a) When using Built-in SMDR
(b) When not using Built-in SMDR
2. PRECAUTION:
None
PORT LOCATION
NUMBERPURPOSES CONNECTOR
Port 0 Local MAT D-SUB connector...

ND-45669  (E)   CHAPTER 3
CM 40
4.  DATA  T ABL E:
3.  ASSIG NM EN T P R O CEDUR E:
DATAPO RT LO CAT IO N  NU MBERD E +
40Y Y+
+ ++DE  EXE+