NEC Neax2000 Ivs Command Manual

CHAPTER 3 ND-45669 (E)
Page 216 Addendum-002
Revision 2.2 JANUARY, 1999
CM49
COMMAND CODE
TITLE:
DIGITAL ANNOUNCEMENT TRUNK
49
YY DIGITAL 
ANNOUNCEMENT 
TRUNK CIRCUIT/
TENANT No.SENDING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
01 Message No. of 
1st Answering 
Message of 
Automated 
AttendantXX:  Tenant Number
(00 – 63)XX Message Number (00 – 63)
assigned by CM49 YY=00
02 Message No. of 
2nd Answer-
ing Message/
Night Message 
of Automated 
Attendant
05 Message No. of 
Hold ServiceCM48 Y=0
06...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 216-1
AUGUST, 1998 Revision 2.1
CM49
COMMAND CODE
TITLE:
DIGITAL ANNOUNCEMENT TRUNK
49
YY DIGITAL 
ANNOUNCEMENT 
TRUNK CIRCUIT/
TENANT No.SENDING DATA
RELATED
COMMAND
No. MEANING DATA MEANING
13 Message No. of 
Vo i c e  G u i d e00: When message 
waiting is set
01: When service is set
02: When service is 
cancelled
03: When Call For-
warding-All Calls/
Do Not Disturb is 
setXX Message Number (00 – 63)
assigned by CM49 YY=00CM48 Y=2
CM49 YY=00-
17XX
0A Message No....

THIS PAGE INTENTIONALLY LEFT BLANK.
CHAPTER 3 ND-45669 (E)
Page 216-2 Addendum-001
Revision 2.1 AUGUST, 1998
This page is for your notes. 

ND-45669 (E) CHAPTER 3
Addendum-001 Page 217
AUGUST, 1998 Revision 2.1
CM50
COMMAND CODE
TITLE:
COMMON ROUTE INDIAL
50
1. FUNCTION:
This command is used to assign LDNs (Listed Directory Numbers) to DID or Tie lines. When these
numbers are dialed into the system, either on an incoming tie line or an incoming C.O. line set up for
indialing, the call will appear at a specified call identification key on the attendant’s console.
The system allows digits to be added to or deleted from indialed numbers on a...

CHAPTER 3 ND-45669 (E)
Page 218 Addendum-001
Revision 2.1 AUGUST, 1998
CM50
COMMAND CODE
TITLE:
COMMON ROUTE INDIAL
50
4 . D ATA  TA B L E :
Note 1:CM35 YY = 17 allows digits to be added or deleted from indialed digit streams on a route basis.
Note 2:“C” or “D” should not be assigned as the first characters of an access code to insert a prepause
timing. The prepause timing should be assigned with CM41 YY=0 Function No. 44.
Note 3:If “C” is inserted in the access code, it can be used as a pause (1.5 sec)....

ND-45669 (E) CHAPTER 3
Pag e 2 19
Revision 2.0
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
4. DATA TABLE:
1. FUNCTION:
This command is used to define destinations for different types of diversion.
2. PRECAUTION:
If a transferred station number for a house phone call and a transferred station number for off-hook
alarm are the same, this service is not effective.
3. ASSIGNMENT PROCEDURE:
YYGROUP NUMBER SETTING DATA
No. MEANING DATA MEANING
00 00
63Tenant 00
Tenant 63For DID line, transfer...

CHAPTER 3 ND-45669 (E)
Pag e 2 20
Revision 2.0
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
10 00
63Tenant 00
Tenant 63Transfer destination of the call when the called 
station is set to Do Not Disturb.X
XXXXStation Number as the 
destination of a call 
diversion. 
In case ATT is desig-
nated as the destina-
tion, the setting data is 
as follows: 
ATT=E 000 (Fixed) 11 00
63Tenant 00
Tenant 63Transfer destination of the call when the Room 
Cut Off station dials C.O. access code.
12 00...

ND-45669 (E) CHAPTER 3
Addendum-001 Page 221
AUGUST, 1998 Revision 2.1
CM51
COMMAND CODE
TITLE:
AUTOMATIC TRANSFER DESTINATIONS
51
YYGROUP NUMBER SETTING DATA
No. MEANING DATA MEANING
18 00
63Tenant 00
Tenant 63Destination VMS of a call that is set Camp-On 
and not answered/Destination VMS of Call Re-
direct.X
XXXXVMS Station No.
20 00
63Tenant 00
Tenant 63Destination VMS station for Call Forwarding-
Not AvailableX
XXXXVMS Station No.
21 00
63Tenant 00
Tenant 63Destination of Alternate Hold Recall for...

CHAPTER 3 ND-45669 (E)
Pag e 2 22
Revision 2.0
CM52
COMMAND CODE
TITLE:
HOT LINE
52
MAT
1. FUNCTION:
This command is used to assign a Hot Line to stations, ATTCONs and trunks.
2. PRECAUTION:
(1) The maximum number of Hot Lines is 100, and the connection is one way from the calling side to
the called side. Thus, for connection in the opposite direction, the calling and called side must be
assigned to another Hot Line number. If all the Hot Lines are to be made bothway lines, the maxi-
mum number of Hot...

ND-45669 (E) CHAPTER 3
Pag e 2 23
Revision 2.0
CM52
COMMAND CODE
TITLE:
HOT LINE
52
MAT
4. DATA TABLE:
4.1 Hot Line
4.2 FAX Incoming Call Lamp Indication
YY
CALLING/CALLEDSETTING DATA
No. MEANING DATA MEANING
00
99Hot Line Num-
ber 00 ~ 990 Calling Side X
XXXXStation Number/Data Station Number
(See CM12 YY = 03)
1 Called Side X
XXXXStation Number/Data Station Number
E000 ATTCON
01XX Hotline-Outside
XX represents the abbreviated code for System 
Speed Dialing (See CM71 and CM72)
YY
CALLING/CALLEDSETTING...