NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 217
Paging Console P-34
Assignment Procedure 
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 73b
0Type of Paging Service
b
1b0b1b0 
00=No Answer 10= Delay
0 1 = None Delay 1 1 = Delay with Paging Transfer b
1
b2
Radio Page Number
(SIM/IMG = 2 Digits only)
0/1 = 2 digits/3 digits
b
3Paging Cancel Code
0/1 = Individual Paging Route Codes/Common to all Paging Routes
b
4Radio Paging – station number is automatically sent.
0/1 = Out/In...

NEAX2400 IMX Hotel Feature Programming Manual
Page 218ND-70284 (E), Issue 2
P-34 Paging Console
4AHSY
INDEX
104b
0Miscellaneous Timer Class (MTC) is to be assigned a 
value from 0 Hex to F Hex (0–15).Paging Console 
Automatic Recall Timer:
Timer Value Setting is 
MTC ×
×× × TC sec.
Note:
When this data is 
00 Hex, ROM 
data is 
automatically set 
to 3 min. b
1
b2
b3
b4Timer Class Length (TCL) is to be assigned one of the 
following values:
b
6b5b4b6b5b4
000= – 100= 64 sec.
001= 8 sec.  101= –
010= 16...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 219
Room Cutoff R-9
R-9 Room Cutoff
General Description
This feature allows the Console, PMS terminal, or Front Desk Terminal to temporarily restrict outgoing CO calls
from guest room telephones while the guests are away.
Operating Procedure
To set ROOM CUTOFF from Console or Front Desk Terminal:
Note:
 If the “RC” steady display is available by system data, the following will display on a Guest station Dterm:

To cancel ROOM...

NEAX2400 IMX Hotel Feature Programming Manual
Page 220ND-70284 (E), Issue 2
R-9 Room Cutoff
Service Conditions
1. Stations in ROOM CUTOFF mode that attempt to access C.O. lines will be routed to a reorder tone
connection, the Console, or an announcement on a system-wide basis.
2. Stations in ROOM CUTOFF mode may be able to place outgoing C.O. calls via the Attendant, depending
on the restriction data assigned via the MAT.
3. ROOM CUTOFF is available for guest room stations only.
4. Through system data...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 221
Room Cutoff R-9
Note:
If unconditional restriction is set as per the OG restriction and IC restriction information, or if OG restriction and IC
restriction are set to Guest stations, the present Route Restriction Class is temporarily replaced with RSC 13–15, and
whether restriction is executed or not is selected from the Restriction Table. 2SYS1
ASYD
INDEX
170b
0Room status data (b2, b1, b0) to be set at the time of Checkout
b...

NEAX2400 IMX Hotel Feature Programming Manual
Page 222ND-70284 (E), Issue 2
R-10 Room Status
R-10 Room Status
General Description
This feature provides a ROOM STATUS display on the Console or Front Desk Terminal. The ROOM STATUS
display indicates the following:
AUTOMATIC WAKE-UP  [A-10]
DO NOT DISTURB  [D-11]
GUEST NAME DISPLAY through PMS  [G-5]
MESSAGE WAITING  [M-6]
ROOM CUTOFF  [R-9]
Room Occupied
Room Reserved
Station number
VIP (PMS option)
Operating Procedure
To display ROOM STATUS on the Console...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 223
Room Status R-10
Assignment Procedure
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
11b
0I/O Port designation to Hotel Printer (Model 60/90/120 PMS)
b
1
b2
b3
Not Used b4
b5
b6Transmission Protocol between PBX and Hotel Printer
b
7
2SYS1
ASYD
INDEX
168b
0Group Announcement Service (for Hotel system)
0/1 = Out/In Service
b
1Audit Reports
0/1 = Out/In Service
b
2Not used
b
3
b4Off-Hook Alarm (service)
0/1 = Out/In Service
b...

NEAX2400 IMX Hotel Feature Programming Manual
Page 224ND-70284 (E), Issue 2
R-10 Room Status
4AHSY
INDEX 
179b
0
Not used b1
b2
b3
b4Designation of Guest Station Access Code
b
7b6b5b4ACC · CODE b7b6b5b4ACC · CODE
0000 Out of Service 0 1 1 1 7
0001 1 1 0 0 0 8
0010 2 1 0 0 1 9
0011 3 1 0 1 0 0
0100 4 1 0 1 1 *
0101 5 1 1 0 0 #
0110 6 b5
b6
b7
STEP CMND BIT EXPLANATION 

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 225
Room Numbering R-17
R-17 Room Numbering
General Description
This feature enables flexible assignment of station numbers based on the guest ROOM NUMBERING plan.
Operating Procedure
Guest room calls are completed in the same manner as calls to ordinary stations.
Service Conditions
1. The same station number cannot be assigned to more than one station in the system.
2. Guest numbers must be contained within Tenant 1.
3. One-, two-,...

NEAX2400 IMX Hotel Feature Programming Manual
Page 226ND-70284 (E), Issue 2
R-17 Room Numbering
Assignment Procedure
Note:
If the data is assigned as “1”, only use commands AANP & AAST to assign Administration and Guest Station
Numbering Plan. If data “0” is assigned, use AANP & AAST for Administration Numbering Plan, and AGNP & AGST
for Guest Numbering Plan. STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
160b
0Hotel Feature required (Fixed Data)
b
1Hotel Service kind (Fixed Data)
b
2Length of Room Status...