NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 227
Split Access S-17
S-17 Split Access
General Description
This feature allows stations which are differentiated by Guest/Administration data, CLASS OF SERVICE –
INDIVIDUAL [C-15] data (Service Feature Class, Telephone Equipment Class, Route Restriction Class) or Day/
Night information to dial the same access codes but access different service features or trunk routes.
Operating Procedure
System data programming is performed from...

NEAX2400 IMX Hotel Feature Programming Manual
Page 228ND-70284 (E), Issue 2
S-17 Split Access
When the Numbering Plan Table is used in common for both Administration Stations and Guest Stations: 
STEP CMND BIT EXPLANATION
1SYS1
ASYD
INDEX 
160b
0Hotel Feature required (Fixed Data)
b
1Hotel Service kind (Fixed Data)
b
2Length of Room Status Memory
0/1 = 8 byte/24 byte
b
3Pattern of Key Arrangement on Hotel Console
(Refer to Table 4) (Usually, 00)
b
4
b5Guest Name Service 
0/1 = Out/In Service
b...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 229
Screening (Split Hold) S-32
S-32 Screening (Split Hold)
General Description
This feature provides the Attendant with a special SCRN key which lets them selectively extend calls which require
SCREENING, and process other calls while waiting for the called station to answer. This is especially helpful when
the Attendant is responding to a VIP call which requires special handling, but must also enter other loops because
other calls...

NEAX2400 IMX Hotel Feature Programming Manual
Page 230ND-70284 (E), Issue 2
S-32 Screening (Split Hold)
2SYS1
ASYD
INDEX 
161b
0Don’t Disturb Override key on Console
0/1 = Out/In Service
b
1Message Waiting Lamp in Service
0/1 = Out/In Service
b
2Language Service
0/1 = Out/In Service
b
3Split Hold Service
0/1 = Out/In Service
b
4Not used
b
5DSS (Direct Station Section) Keys on Console
0/1 = Out/In service
b
6Timing Start using “#” Code
0/1 = Ineffective/Effective
b
7Timing Start using “*” Code
0/1 =...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 231
Service Call Routing S-49
S-49 Service Call Routing
General Description
The SERVICE CALL ROUTING feature allows several extensions to be assigned the same number with different
terminations by differentiating between a main building and annex, or between floor numbers. This makes it
possible to set up service stations that are assigned the same number at several places in the hotel.
Operating Procedure
To call a service...

NEAX2400 IMX Hotel Feature Programming Manual
Page 232ND-70284 (E), Issue 2
S-74 Secretarial Service – Guest Station
S-74  Secretarial Service – Guest Station
General Description
This feature allows the Console to temporarily set two or more guest stations to operate in a boss/secretary
arrangement. All calls to the boss are diverted to the secretary. The secretary may screen the calls and then transfer
the call to the boss or just take messages.
Operating Procedure
To set SECRETARIAL SERVICE – GUEST...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 233
Secretarial Service – Guest Station S-74
Operating Procedure (cont’d)

To cancel SECRETARIAL SERVICE – GUEST STATION from the Hotel Console:

To call the Secretary Station from the Boss’ Station:
Step Action Result
1
Press the SCR key.The following is displayed at the Hotel Console:
2Dials the secretary’s 
station number.The display changes to display the secretary’s station number:
3Press the ENTER key.The display changes as...

NEAX2400 IMX Hotel Feature Programming Manual
Page 234ND-70284 (E), Issue 2
S-74 Secretarial Service – Guest Station
Operating Procedure (cont’d)
To call the Boss’ Station from the Secretary Station:
Note:
When more than one Boss’ Station are set, dial the Station number of each Boss after dialing access code.

To transfer an incoming call from the secretary to boss:
Service Conditions
1. AUTOMATIC WAKE-UP [A-10] and VIP WAKE-UP calls go to the boss station, not to the secretarys
station.
2. The...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 235
Secretarial Service – Guest Station S-74
Service Conditions (cont’d)
9. An incoming call to the Boss’ Station is automatically transferred to the secretary’s station. If the
secretary’s station is busy, the caller hears the busy tone. If the secretary has Call Forward – Busy set, the
call rings at the CFW – Busy destination.
Assignment Procedure 
STEP CMND EXPLANATION
1AANP
or
AGNPAssign the minimum necessary number of digits...

NEAX2400 IMX Hotel Feature Programming Manual
Page 236ND-70284 (E), Issue 2
S-75 Suite Room Service
S-75 Suite Room Service
General Description
The SUITE ROOM SERVICE feature allows up to four analog stations to serve one suite room. Each telephone will
have its own station number. One station is designated as the primary station. When the primary station is called,
any secondary station in the suite may answer.
Operating Procedure
To answer a call:
To originate a call:
Service Conditions
1. Each of...