NEC Neax 2400 Imx Hotel Feature Programming Manual

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 237
Suite Room Service S-75
Service Conditions (cont’d)
7. The station number displayed on the Dterm or Console is the primary station number or phantom number,
regardless of the telephone used in the suite room.
8. There is no limitation to the number of suites in a system.
9. If digital remote units are used for suite room service, ringing cannot be synchronized.
10. PMS registers all hospitality activity against the primary...

NEAX2400 IMX Hotel Feature Programming Manual
Page 238ND-70284 (E), Issue 2
S-75 Suite Room Service
Service Conditions (cont’d)
19. The primary station number of the suite room must be assigned as the my line number of the Dterm. When
one Dterm is used in a suite (sub lines will be virtual stations):
a.) The my line number will be the prime line number, and it should be assigned as the primary
station number of the suite room.
b.) The primary station number is used for the interface to PMS.
c.) All sub...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 239
Suite Room Service S-75
Assignment Procedure 
STEP CMND BIT EXPLANATION
1AHSY
INDEX 
111b
0Fixed Data
b
1
b2Restriction for hooking when an outgoing C.O. line call has originated from a suite room
0/1 = Restriction/No Restriction
b
3Setting of Message Registration Data to be sent out to the PMS
b
4b3 
 0 0 = The pilot number is sent out in the case of Suite Room; the Main Room Station 
Number is sent out in the case of...

NEAX2400 IMX Hotel Feature Programming Manual
Page 240ND-70284 (E), Issue 2
S-75 Suite Room Service
Note:
To skip data entry, press the Enter key to step to the next data entry field. 3AHSY
INDEX 
189b
0
Not used b
1
b2
b3
b4
b5
Suite Room Individual Station Calling
0 =  A Suite Room individual station can be called from a Guest Station, Administration 
Station, and Console.
1 =  A Suite Room individual station can be called from a Special Administration Station 
and Console.
b
6
Ringing for Connecting...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 241
2nd Wake-up Call – Same Guest Station S-128
S-128  2nd Wake-up Call – Same Guest Station
General Description
By combining with AUTOMATIC WAKE-UP [A-27] service, this service allows two wake-up calls to be set for a
guest room.
Operating Procedure
The notice asking the guest to call the Attendant when the guest wants to set the second wake-up call should be
prepared in the guest room. The guest sees the notice and calls the...

NEAX2400 IMX Hotel Feature Programming Manual
Page 242ND-70284 (E), Issue 2
S-128 2nd Wake-up Call – Same Guest Station
Operating Procedure (cont’d)
To cancel the second wake-up call using the WUR key:
When the guest calls in to cancel the second wake-up call (see DIRECT SERVICE SET/RESET [D-25]):
If the wake-up cancel is entered after the guest line is released:
To set the second wake-up call using the WUS key and the service set code:
Note 1:
In case of using a Dterm for a guest station, if the...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 243
2nd Wake-up Call – Same Guest Station S-128
Service Conditions
1. When setting the second wake-up call, the attendant can select whether to set it as AUTOMATIC WAKE-
UP [A-27] service or AUTOMATIC WAKE-UP – HOTEL ATTENDANT ASSISTANCE [A-58]
service.
2. This service can be set/cancelled from the Console or the PMS Terminal (Model 90 and 120 only).
However, when setting from the PMS Terminal, AUTOMATIC WAKE-UP – HOTEL ATTENDANT...

NEAX2400 IMX Hotel Feature Programming Manual
Page 244ND-70284 (E), Issue 2
S-128 2nd Wake-up Call – Same Guest Station
Service Conditions (cont’d)
15. When 2ND WAKE-UP CALL is executed, the LCD displays as shown below:
16. When the guest room D
term answers the second wake-up call, “WAKE UP” display will remain.
17. For the conditions of the LCD display when several services are set at the same time, see Service
Conditions of AUTOMATIC WAKE-UP – D
term [A-27D].
Assignment Procedure
See [A-10] Assignment...

NEAX2400 IMX Hotel Feature Programming Manual
ND-70284 (E), Issue 2
Page 245
Toll Terminal Access T-13
T-13  Toll Terminal Access
General Description
This feature enables guest stations to directly access toll trunks. Access may be arranged on a direct-dial or
attendant-assisted basis, depending on the associated Central Office.
Operating Procedure
To operate:
Service Conditions
Guest stations must be assigned the proper Route Restriction Class to gain TOLL TERMINAL ACCESS.
Assignment Procedure 
Action...

NEAX2400 IMX Hotel Feature Programming Manual
Page 246ND-70284 (E), Issue 2
T-21 Timing Start
T-21 Timing Start
General Description
This feature allows single-digit and multi-digit stations to use the same numbering plan levels by providing a
predetermined time delay between the completion of dialing and the start of ringing. By pressing the # or * key after
dialing the station number, the station user will not have to wait for ring start. By pressing the START key on the
Console, the attendant will not...