NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual

CHAPTER 4 NDA-24282
Pag e 6 2
Revision 1.0
PA-AL16 (ALMC)
SW4
1OFF×Alarm Bus Fixed
2OFF×Alarm Bus Fixed
3OFF×Alarm Bus Fixed
4OFF×Alarm Bus Fixed
SW5 1 ON×Fixed
2OFF×Fixed
3OFF×Fixed
4ON For ACDP Dual System Configuration
OFF For ACDP Single System Configuration
SW6
1OFF×Alarm Bus Fixed
2OFF×Alarm Bus Fixed
SWITCH NAMESWITCH 
NO.SETTINGSTANDARD
SETTINGMEANING
ON1234
ON1234
12ON 

NDA-24282 CHAPTER 4
Page 63
Revision 1.0
PA-AL16 (ALMC)
SWITCH SETTING SHEET
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
APM 20 MB UP: Circuit card make busy
DOWN:Circuit card make idle
EMASUP
CPUSEL Middle = ACDP Dual System
Down = ACDP Single System
MG (SW3) 0 = Single CPU Systems
9 = Multi CPU Systems
SW0
SW1 2 and 4 ON (Fixed)
SW2
SW4 Alarm Bus
SW5 4 ON = Dual ACDP
4 OFF = Single ACDP
SW6 Alarm BusON
ON
ON
0
9
ON
1234
ON
1234
12ON
ON
1234
ON
1234
12 ON 

CHAPTER 4 NDA-24282
Pag e 6 4
Revision 1.0
PH-PC21 (APINT)
PH-PC21 (APINT)
1. Function
This circuit card is an inter-processor interface card and is used only for the Module Type ACD.
The card provides FIFO for mutual I/O bus connections for processor communication between the system
CPU and the ACDP.
2. Mounting Location/Condition
The mounting location of this circuit card and the condition related to mounting are shown below.
GATE
CPU
MEMECPYGATE
CPU
MEMAPINT APINT 
ACD Module
8-bit I/O Bus
Extended...

NDA-24282 CHAPTER 4
Page 65
Revision 1.0
PH-PC21 (APINT)
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
5. Switch Settings
Standard settings of various switches on this circuit card are shown in the table below.
LAMP NAME COLOR STATE
OPE/MBGreen Remains lit while this circuit card is operating.
Red Lights while...

CHAPTER 4 NDA-24282
Pag e 6 6
Revision 1.0
PH-PC21 (APINT)
SW01ONWhen using this circuit card in the ACDP of 
single-system configuration or when 
connecting this circuit card to No. 0 system of 
the ACDP of dual-system configuration.
OFFWhen connecting this circuit card to No. 1 
system of the ACDP of dual-system 
configuration.
2ON×Fixed
3ONWhen the ACDP is provided by single-system 
configuration.
OFFWhen the ACDP is provided by dual-system 
configuration.
4OFF×Fixed
5OFF×Fixed
6ON
7OFF
8ON
SWITCH...

NDA-24282 CHAPTER 4
Page 67
Revision 1.0
PH-PC21 (APINT)
SWITCH SETTING SHEET
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
LPRJ-A 00
01
02MB UP: Circuit card make busy
DOWN: Circuit card make idle
SW0
ON
ON
1234567
8 

CHAPTER 4 NDA-24282
Pag e 6 8
Revision 1.0
PA-PC56-A (COPY)
PA-PC56-A (COPY)
1. Function
This circuit card provides the function to copy the contents of the RAM of both the standby (ST-Y) system
and the active (ACT) system so that the contents of the RAM of both system may be always coinciding with
each other.
2. Mounting Location/Condition
The mounting locations of this circuit card and the conditions related to mounting are shown below.
  This circuit card is not used when the ACDP is provided in a...

NDA-24282 CHAPTER 4
Page 69
Revision 1.0
PA-PC56-A (COPY)
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
LAMP NAME COLOR STATE
OPE Green Remains lit while this circuit card is operating in ACT state.
COPY Green Remains lit while this circuit card is operating in COPY mode.
OPE
SREQ
SW0MB
MBS1
COPY
MBS0 

CHAPTER 4 NDA-24282
Pag e 7 0
Revision 1.0
PA-PC56-A (COPY)
5. Switch Settings
Standard settings of various switches on this circuit card are shown in the table below.
SWITCH 
NAMESWITCH NO. SETTINGSTANDARD 
SETTINGMEANING
MBUP Circuit card make busy.
DOWN Circuit card make idle.
SREQUP Separate mode request.
DOWN Separate mode request cancel (Copy mode).
SW01ONTo be set in the case of System No. 0.
(To be mounted in Slot No. 08 of APMA.)
OFFTo be set in the case of System No. 1.
(To be mounted in Slot...

NDA-24282 CHAPTER 4
Page 71
Revision 1.0
PA-PC56-A (COPY)
SWITCH SETTING SHEET
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
APM-A\E 08
17MB UP: Circuit card make busy
DOWN:Circuit card make idle
SREQ
SW0 1 ON = System No. 0
1 OFF = System No. 1ON
ON
ON
12345678