NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual

CHAPTER 4 NDA-24282
Pag e 9 2
Revision 1.0
PH-BS16 (PBI)
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
LAMP NAME COLOR STATE
AC TGreen Remains lit while the CPU which controls this circuit card is in ACT state.
Red Lights with PBI Make Busy switch and MB switch turned on.
OPE Green Lights when the CPU has accessed to this circuit card.
PWRALM  Red Lights when the On-Board Power Supply equipped on this circuit card is faulty.
EQBY Green Remains lit...

NDA-24282 CHAPTER 4
Page 93
Revision 1.0
PH-BS16 (PBI)
5. Switch Settings
Standard settings of various switches on this circuit card are shown in the table below.
SWITCH NAMESWITCH 
NO.SETTINGSTAN-
DARD 
SETTINGMEANING
MB
UP Circuit card make busy.
DOWN×Circuit card make idle.
PBIH 
7×Fixed
PBIL
0Not used.
~
7Not used
8ACDP0-System No. 0 (Mounted in Slot No. 13 
of APMA0) (standard setting)
9ACDP0- System No. 1(Mounted in Slot No. 14 
of APMA0) (standard setting)
AACDP1-System No. 0 (Mounted in Slot No....

CHAPTER 4 NDA-24282
Pag e 9 4
Revision 1.0
PH-BS16 (PBI)
SWITCH SETTING SHEET
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
13
14MB UP: Circuit card make busy
DOWN:Circuit card make idle
PBIH 7: Fixed
PBILON
7 

NDA-24282 CHAPTER 4
Page 95
Revision 1.0
PA-GT17 (SPGT)
PA-GT17 (SPGT)
1. Function
This circuit card is used when the MISCME module is required. This circuit card provides flow control and
terminates the extention of the MISC bus. This circuit card also controls the alarm LEDs equipped in the
To p  U n i t .
Figure 4-2   Position in IMGdxh
Single Configuration
IMG0LOCAL I/O BUS
TSW
GT
GTA
GTA
GTA To IMG 1
To IMG 2
To IMG 3
EXGT
EMA
IOC
MISC BUSCPRB-A
HDD
FDD
APINT APINT APINT APINTMISCME
SPGT
INT
IMG0...

CHAPTER 4 NDA-24282
Pag e 9 6
Revision 1.0
PA-GT17 (SPGT)
2. Mounting Location/Conditions
The SPGT card mounts in the MISCME as shown below.
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module MISCME
SPGTSPGT
SW10OPE
MB
CLK ALM
DSPP
ALM 

NDA-24282 CHAPTER 4
Page 97
Revision 1.0
PA-GT17 (SPGT)
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
5. Switch Setting
Standard settings of various switches on this circuit card are shown in the table below.
LAMP NAME COLOR STATE
OPE Green Remains lit while this circuit card is operating.
CLK ALM Red Lights when a clock down occurred.
SWITCH 
NAMESWITCH 
NO.SETTINGSTANDARD
SETTINGMEANING
MBON Circuit card make busy.
OFF×Circuit card make idle....

CHAPTER 4 NDA-24282
Pag e 9 8
Revision 1.0
PA-GT17 (SPGT)
Switch Setting Sheet
MODULE SLOT NO.SWITCH 
NAMESWITCH SHAPE REMARKS
MISCME 22 and 23MBUP: Circuit card make busy
DOWN: Circuit card make idle
SW0
ON
ON
12 

NDA-24282 CHAPTER 4
Page 99
Revision 1.0
PA-16ELCDD (ELC)
PA-16ELCDD (ELC)
1. Function
This circuit card is a line card which supports the interface of HDAC. When using voice only, 16 lines of
HDAC can be connected to this circuit card. Further, by changing the switch setting, this circuit card can be
connected with eight (8) lines respectively of voice terminals and data terminals.
NUMBER OF 
LINE 
CIRCUITSNUMBER OF 
TIME SLOTSDATA COMMUNICATION FUNCTION REMARKS
8DLC Mode 8 circuits 16 Time Slots...

CHAPTER 4 NDA-24282
Pag e 1 00
Revision 1.0
PA-16ELCDD (ELC)
2. Mounting Location/Condition
The mounting locations of this circuit card and the conditions related to mounting are shown below.
(a) When this circuit card is mounted in PIMA
(b) When this circuit card is mounted in PIMB
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module PIMU-A
00 01 02 03 04 05 06 07 08 09 10 11 12 13 14 15 16 17 18 19 20 21 22 23
Mounting Module PIMB
Note: 
 indicates the mounting...

NDA-24282 CHAPTER 4
Page 101
Revision 1.0
PA-16ELCDD (ELC)
3. Face Layout of Lamps, Switches, and Connectors
The face layout of lamps, switches, and connectors of this circuit card is shown below.
4. Lamp Indications
The contents of lamp indications of this circuit card are shown in the table below.
LAMP NAME COLOR STATE
OPE  Green Remains lit while this circuit card is in operating normally.
N-OPE  Red Remains lit while this circuit card is isolated from the system.
PWRALM Red Lights when power supply...