NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual
Here you can view all the pages of manual NEC Neax 2400 Imx Callcenterworx Enterprise Acd System Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 71
CHAPTER 4 NDA-24282 Pag e 5 2 Revision 1.0 PH-PC22 (EAPI) SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING SW01 (for Port 0) SW11 (for Port 1) (When using AC D-M IS Interface Port)1 2 3 4ON×Sets the non-protocol RS-232C port stop bit length to 1 bit. OFFSets the non-protocol RS-232C port stop bit length to 2 bit. 5ON×Sets the non-protocol RS-232C port data length to 7 bit. OFFSets the non-protocol RS-232C port data length to 8 bit. 6 7 8ONSets the polarity of non-protocol RS-232C PB signal...
Page 72
NDA-24282 CHAPTER 4 Page 53 Revision 1.0 PH-PC22 (EAPI) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS LCMA 02 03 04MB UP: Circuit card make busy MBR DOWN: Circuit card make idle LPRJ-A 00 01 02SW0 SW01 9600 bps Port 0, 1 Stop 7 Even SW11 9600 bps Port 1, 1 Stop 7 Even DOWN DOWN ON 12345678 ON 12345678 ON 12345678
Page 73
CHAPTER 4 NDA-24282 Pag e 5 4 Revision 1.0 PH-PC27 (EAPI) PH-PC27 (EAPI) 1. Function This circuit card is an I/O system functions integrated card to be used in the ACD Circuit Card Type System. This card supports the following functions. (a) APINT Function: For processor communications between the CPU of the System and ACDP card, this circuit card provides FIFO for mutual I/O bus connections. (b) IOC Function: For ACD-MIS connection, this circuit card provides a serial interface which conforms with...
Page 74
NDA-24282 CHAPTER 4 Page 55 Revision 1.0 PH-PC27 (EAPI) 3. Face Layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. 00 01 02 03 04 Mounting Module LPRJ-A PH-PC27 PH-PC27 PH-PC27 Note CPRAC-0 CPRAC-1 Note:This circuit card is mounted in any one of Slot No. 00~02. IOC OPE CLKALM OPE/MB MB SW10 SW12 SW11 MBR SW0to CP-53 to CP-53 AP-1 AP-0
Page 75
CHAPTER 4 NDA-24282 Pag e 5 6 Revision 1.0 PH-PC27 (EAPI) 4. Lamp Indications The contents of lamp indications of this circuit card are shown in the table below. 5. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. LAMP NAME COLOR STATE OPE/MB Green Remains lit while this circuit card is operating. IOCOPE Red Remains lit while the non-protocol/RS-232C Port Controller is operating normally. CLKALM Red Lights when a clock failure has occurred....
Page 76
NDA-24282 CHAPTER 4 Page 57 Revision 1.0 PH-PC27 (EAPI) Note: Ports 0, 1 and 2 translate to MIS ports 1, 2 and 3. SWITCH NAMESWITCH NO. SETTINGSTANDARD SETTINGMEANING SW10 (for Port 0) SW11 (for Port 1) SW12 (for Port 2)1 2 3 MIS Port Interface 4ON×Sets the non-protocol RS-232C port stop bit length to 1 bit. OFFSets the non-protocol RS-232C port stop bit length to 2 bit. 5ON×Sets the non-protocol RS-232C port data length to 7 bit. OFFSets the non-protocol RS-232C port data length to 8 bit. 6 7...
Page 77
CHAPTER 4 NDA-24282 Pag e 5 8 Revision 1.0 PH-PC27 (EAPI) SWITCH SETTING SHEET MODULE SLOT NO.SWITCH NAMESWITCH SHAPE REMARKS LCMA 02 03 04MB UP: Circuit card make busy. MBR DOWN: Circuit card make idle. LPRJ-A 00 01 02SW0 SW10 2, 4, 5, 6 ON only SW11 2, 4, 5, 6 ON only SW12 2, 4, 5, 6 ON only DOWN DOWN ON 12345678 ON 12345678 ON 12345678 ON 12345678
Page 78
NDA-24282 CHAPTER 4 Page 59 Revision 1.0 PA-AL16 (ALMC) PA-AL16 (ALMC) 1. Function This circuit card collects fault information and manages a dual-configuration system of the ACD Module Type System. The card displays the collected fault information on the TOPU. Besides, the card provides the functions for data communication between two ACDPs in the dual system configuration. 2. Mounting Location/Condition The mounting location of this circuit card and the condition related to mounting are shown below....
Page 79
CHAPTER 4 NDA-24282 Pag e 6 0 Revision 1.0 PA-AL16 (ALMC) 3. Face layout of Lamps, Switches, and Connectors The face layout of lamps, switches, and connectors of this circuit card is shown below. MBR SW1 EMA SUP MG SW5 SW4 SW6 SW0 SW2 (SW3)CPUSEL
Page 80
NDA-24282 CHAPTER 4 Page 61 Revision 1.0 PA-AL16 (ALMC) 4. Switch Settings Standard settings of various switches on this circuit card are shown in the table below. Note 1:For IMG (IMX) (ICS), IMGx, IMGxh Note 7:For MMG (ICS), UMG (ICS), UMGx SWITCH NAMESWITCH NO.SETTINGSTANDARD SETTINGMEANING MBUP Circuit card make busy. DOWNCircuit card make idle. EMASUP UP×Fixed DOWN CPUSEL UP MIDDLEFor ACDP Dual System Configuration DOWNFor ACDP Single System Configuration MG (SW3) 0Single CPU System Note 1 9Multi...