NEC Neax 2400 Imx Business Features And Specifications

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 91
Call Forwarding - Don’t Answer - DtermC-3D
Service Conditions (cont’d)
9. A user may set CALL FORWARDING - DONT ANSWER - Dterm for a multi-line appearance based on
the CLASS OF SERVICE - INDIVIDUAL [C-15] as assigned to the station (MY Line) setting the service.
The figure below is a simplified key sheet assignment for stations 200 & 201. The CLASS OF SERVICE
- INDIVIDUAL [C-15] for station 200 is allowed CALL FORWARDING - DONT...

NEAX2400 IMX Business Features and Specifications
Page 92NDA-24221, Issue 3
C-3D Call Forwarding - Don’t Answer - Dterm
Service Conditions (cont’d)
14. Call Transfer - Attendant (Station): Station calls transferred by the Attendant are assigned this feature
according to TENANT SERVICE [T-12] class of the originating and destination stations when the called
station does not answer for a predetermined time interval. When restricted by TENANT SERVICE class,
this feature is not activated, and the called...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 93
Call Forwarding - All Calls C-5
C-5 Call Forwarding - All Calls
General Description
This feature permits all calls destined for a particular station to be routed to another station (or to the Attendant)
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by either
the individual user or the Attendant.
Operating Procedure
To activate CALL FORWARDING - ALL CALLS from an...

NEAX2400 IMX Business Features and Specifications
Page 94NDA-24221, Issue 3
C-5 Call Forwarding - All Calls
Service Conditions (cont’d)
9. When the user setting CALL FORWARDING - ALL CALLS goes off-hook, special dial tone can be
provided instead of dial tone. (Activation of this service is determined by system data.)
10. The OAI monitor number and the ACD pilot number cannot be assigned as the Call Forwarding target
telephone number except when called from a station or Tie Line trunk.
11. When a...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 95
Call Forwarding - All Calls C-5
Interactions (cont’d)
9. CALL FORWARDING-ALL CALLS can be overridden, allowing Station B to initiate or transfer calls
back to Station A.
10. STATION-TO-STATION CALLING [S-11] must first be provided. 

NEAX2400 IMX Business Features and Specifications
Page 96NDA-24221, Issue 3
C-5D Call Forwarding - All Calls - Dterm
C-5D  Call Forwarding - All Calls - Dterm
General Description
This feature permits all calls destined for a particular station to be routed to another station, or to the Attendant,
regardless of the busy or idle status of the called station. Activation and cancellation may be accomplished by the
user or the Attendant. CALL FORWARDING - ALL CALLS - D
term may be set or cancelled by the user...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 97
Call Forwarding - All Calls - DtermC-5D
Operating Procedure (cont’d)
3. Dial the desired target telephone number; receive service set tone. The LED of the associated feature key
does not light at the station setting the service. If the multi-line appearance is another Dterms MY Line,
that stations feature key LED will light. The setting stations LCD displays:
Target Station
4. Replace the handset or press the SPEAKER key.
5. If...

NEAX2400 IMX Business Features and Specifications
Page 98NDA-24221, Issue 3
C-5D Call Forwarding - All Calls - Dterm
Service Conditions (cont’d)
7. A user may set CALL FORWARDING - ALL CALLS - Dterm for a multi-line appearance based on the
CLASS OF SERVICE - INDIVIDUAL [C-15] assigned to the station setting the service. The figure below
is a simplified key sheet assignment for stations 200 & 201. The CLASS OF SERVICE - INDIVIDUAL
[C-15] for station 200 is allowed CALL FORWARDING - ALL CALLS - D
term, but...

NEAX2400 IMX Business Features and Specifications
NDA-24221, Issue 3
Page 99
Call Forwarding - All Calls - DtermC-5D
Service Conditions (cont’d)
15. A call can be forwarded to an Attendant Console in the remote node via FCCS link.
16. When a call is forwarded through FCCS link, the numbering plans of the originally called station and the
forwarded Attendant Console must be the same.
Interactions
1. Users are unaccustomed to hearing ringback tone when responding to their own station’s ring. Inform
users...

NEAX2400 IMX Business Features and Specifications
Page 100NDA-24221, Issue 3
C-6 Call Hold
C-6 Call Hold
General Description
This feature permits any user to hold a call in progress by performing a switch hook flash and dialing a
preprogrammed CALL HOLD code, thus allowing that line to be used for originating another call or returning to a
previously held call.
Operating Procedure
To hold a call in progress:
1. Press the switch hook; receive special dial tone. 
2. Dial CALL HOLD code; receive normal dial...