NEC Neax 2000 Ivs2 Ccis Features And Specifications
Have a look at the manual NEC Neax 2000 Ivs2 Ccis Features And Specifications online for free. It’s possible to download the document as PDF or print. UserManuals.tech offer 1168 NEC manuals and user’s guides for free. Share the user manual or guide on Facebook, Twitter or Google+.
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS NEAX2000 IVS2 CCIS Features and Specifications NDA-24272, Issue 1.0 Page 1 ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS General Description This feature permits the Attendant, when the desired station at another switching office is busy, to hold an incoming call in a special waiting mode. A distinctive Camp-On tone is sent to the busy station when the Attendant sets Camp-On. When that station becomes idle, it is automatically rung and connected to the waiting trunk party. Station Application Attendant Consoles Operating Procedure To activate an Attendant Camp-on with Tone Indication - CCIS from an Attendant Console: 1. Dial the desired station number at another switching office and receive busy tone. 2. Press the RELEASE key. 3. A Camp-On tone is sent to the busy station and Camp-On is set. To cancel an Attendant Camp-on with Tone Indication - CCIS from an Attendant Console: 1. Press the LOOP key corresponding to the held call and connect to the waiting trunk party. 2. Press the DEST key and receive busy tone. 3. Press the CANCL key. Service Conditions 1. This feature is available from an Attendant Console of either the NEAX2400 IMX or NEAX2000 IVS2 through the CCIS Network. 2. This feature is limited to one call waiting per station line. 3. The maximum number of simultaneous Camp-On calls is 32. 4. Attendant Camp-On may be denied if the busy station is: • Dialing or in Line Lockout mode Receiving a System Generated Tone Being rung Protected from Camp-On by Class of Service Being connected to an Attendant. When Camp-On is denied, the Attendant will receive reorder tone.
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS NEAX2000 IVS2 CCIS Features and SpecificationsPage 2 NDA-24272, Issue 1.0 5. The connecting link between the calling party and the called party will be reserved in the normal manner, and the RELEASE key will be inoperative when the link between the two switching offices cannot be reserved. 6. All calls completed by the Attendant to a busy station are held waiting. A single 128 millisecond burst tone is directed toward the busy station every eight seconds. 7. Only the called station hears the Camp-On tone.
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS NEAX2000 IVS2 CCIS Features and Specifications NDA-24272, Issue 1.0 Page 3 The linking procedure between two switching offices is as shown in Figure 1: Figure 1 Linking Two Offices (1 of 2) Music Public Tributary Office Public Attendant Console MusicBusyDial RELEASEC:6789 C:6789 ATT: RELEASEB:4567 B:4567 Setting Camp-OnMain Office Tributary OfficeSatellite Office Public Attendant Console Main OfficeSatellite Office Public (NEAX2000 IVS 2) (NEAX2400/ NEAX2000 IVS 2)(NEAX2000 IVS 2) (NEAX2000 IVS 2) (NEAX2400/ NEAX2000 IVS 2) (NEAX2000 IVS 2) Network Network Tone(BT) 4567 Network NetworkAttendant Transfer to Busy Station
ATTENDANT CAMP-ON WITH TONE INDICATION - CCIS NEAX2000 IVS2 CCIS Features and SpecificationsPage 4 NDA-24272, Issue 1.0 Figure 1 Linking Two Offices (2 of 2) RBT Main Office Main OfficePublic Music Public RG C:6789B:4567 Called Party ReleaseB:4567 C:6789 ROTB: ON HOOK Attendant Tributary OfficeSatellite Office Public Attendant Tributary OfficeSatellite Office Public (NEAX2000 IVS2) Console Network (NEAX2400/ NEAX2000 IVS 2) (NEAX2000 IVS 2) Network Network Console(NEAX2000 IVS 2) (NEAX2400/ NEAX2000 IVS 2) (NEAX2000 IVS 2) Network Camped On Call hears Music On Hold and Camped On Call Hears Ring Back Tone (RBT) and Station 4567 Rings
ATTENDANT CONTROLLED CONFERENCE - CCIS NEAX2000 IVS2 CCIS Features and Specifications NDA-24272, Issue 1.0 Page 5 ATTENDANT CONTROLLED CONFERENCE - CCIS General Description This feature permits an Attendant (NEAX2400 IMX) to establish a conference, through CCIS, with up to eight parties of stations and/or trunks (inside and outside parties). Operating Procedure To activate an Attendant Controlled Conference - CCIS: 1. A station (conference leader) calls an Attendant (NEAX2400 IMX only) to request a conference. 2. The Attendant connects the conference leader to one of the assigned line circuits. 3. The Attendant sequentially calls all desired parties and connects them to the other assigned line circuits. 4. Once all the parties are connected, any conferee with a push-button telephone may dial a 9 to block additional participants, thereby assuring privacy. 5. If any push-button station user connected to the conference trunk dials 0, all the conferees will be disconnected. Otherwise, the conference is terminated only after all the parties hang up. 6. To be released from the conference trunk individually, a station user hangs up. The remaining conferees can continue without interruption. Service Conditions 1. A conference unit (PA-CFTB) must be mounted on the NEAX2400 IMX. 2. Stations and Attendants of the NEAX2000 IVS 2 system cannot be the conference leader. NEAX2000 IVS2 CCIS Conference leader (ATT CON) CFT NEAX2400
BROKERAGE - HOT LINE - CCIS NEAX2000 IVS2 CCIS Features and SpecificationsPage 6 NDA-24272, Issue 1.0 BROKERAGE - HOT LINE - CCIS General Description This feature provides a ringdown connection between two stations, each using a Multiline Terminal, in different offices in the CCIS Network. Operating Procedure To access a Brokerage - Hot Line - CCIS from a Multiline Terminal: 1. Lift the handset or press the Speaker key. 2. Press the line/feature key associated with the preassigned station. The destination station is automatically dialed, ringback tone is heard and the destination station answers. 3. After completing the conversation, hang up or press the Speaker key. To make another Brokerage - Hot Line - CCIS call immediately, press another line/feature key without going on hook and off hook. Service Conditions Calling party: 1. Any Multiline Terminal, used for this feature, must be assigned a Primary Extension. 2. When a Brokerage - Hot Line - CCIS call is made from a Multiline Terminal with LCD, the LCD shows the destination station number. 3. The feature is applicable for inter-office connections on the CCIS Network. The destinations must be a station or an Attendant Console at different offices. 4. There is a maximum of 100 Brokerage - Hot Line - CCIS destination assignments. 5. Attendant Camp-On, Executive-Right-Of-Way, and Busy Verification can be prohibited to the Brokerage - Hot Line - CCIS connection through Class Of Service-Individual. Called party: 1. A Brokerage - Hot Line - CCIS call can be transferred to another station using the Call Transfer feature. 2. Call Forwarding is applied whenever the destination station of the Brokerage - Hot Line - CCIS call has set Call Forwarding (All Calls, Busy and Don’t Answer). 3. Station hunting works if the destination station is a pilot in a hunt group. The UCD function works if the destination station is a pilot of a UCD group. 4. When a destination is an Attendant Console, the Brokerage - Hot Line - CCIS call terminates as a Tie Line call.
BUSY VERIFICATION - CCIS NEAX2000 IVS2 CCIS Features and Specifications NDA-24272, Issue 1.0 Page 7 BUSY VERIFICATION - CCIS General Description This feature permits an Attendant, via the Attendant Console on the NEAX2400 IMX or the NEAX2000 IVS2, to interrupt a busy station’s call at another switching office connected through CCIS. Operating Procedure To activate a Busy Verification - CCIS: 1. Press an idle LOOP key. 2. Dial the desired station number and receive busy tone. 3. Press the BV key. 4. A two-burst tone is sent to the connected parties. 5. The Attendant may monitor or join the conversation. 6. Press the RELEASE key to disengage. Service Conditions 1. This feature can be activated from an Attendant Console of either the NEAX2400 IMX or the NEAX2000 IVS2 in the CCIS network. 2. This feature can be used to monitor two-party calls (station and trunk or another station). 3. This feature cannot be established to a busy station when the station is: Dialing Listening to a tone Being rung Protected from Busy Verification by Class of Service Being connected to an Attendant
BUSY VERIFICATION - CCIS NEAX2000 IVS2 CCIS Features and SpecificationsPage 8 NDA-24272, Issue 1.0 NEAX2000 IVS2 CCIS ATT To STA/CO/TIE/CCIS BV STANEAX2400 /NEAX2000 IVS2 PBX-APBX-B By dialing the busy station number in PBX-A and pressing Busy/Verification Feature key, the Attendant Console can verify Busy status of any station in PBX-A.
BUSY VERIFICATION - CCIS NEAX2000 IVS2 CCIS Features and Specifications NDA-24272, Issue 1.0 Page 9 The linking procedure between two switching offices is shown in Figure 2: Figure 2 Linking Two Switching Offices Main OfficeBusy Main Office Tributary Office ATT: BVDial C:6789 C:6789B:4567 B:4567 Attendant Console Satellite Office Public Network Tributary Office Attendant Satellite Office Public Network (NEAX2400/ NEAX2000 IVS 2)Tone4567 (BT) (NEAX2000 IVS 2) (NEAX2000 IVS 2) Console (NEAX2000 IVS 2) (NEAX2400/ NEAX2000 IVS 2) (NEAX2000 IVS 2)
CALL BACK - CCIS NEAX2000 IVS2 CCIS Features and SpecificationsPage 10 NDA-24272, Issue 1.0 CALL BACK - CCIS General Description This feature provides inter-office Call Back. A station who has dialed a busy station at another office can set Call Back - CCIS by dialing a feature access code. When this feature has been set, the setting station will ring as soon as the busy station becomes available. Operating Procedure To set a Call Back - CCIS from a Single Line Telephone: 1. Dial the desired station number and receive busy tone. 2. Press the hook switch and receive Feature Dial Tone. 3. Dial the Call Back feature access code and receive Service Set Tone. 4. Replace the handset. 5. When the busy station becomes idle, the setting station will ring. 6. When the setting station answers, the originally called station will ring. To cancel a Call Back - CCIS from a Single Line Telephone: 1. Lift the handset; receive dial tone. 2. Dial the Call Back cancellation code and receive Service Set Tone. To set a Call Back - CCIS from a Multiline Terminal: 1. Dial the desired station number and receive busy tone. 2. Press the Call Back feature key and receive Service Set Tone. The LCD shows: 3. Replace the handset. 4. When the busy station becomes idle, the setting station will ring. The LCD shows: 5. When the setting station answers, the originally called station will ring. Called station number Series III Series E SET XXXX (TIME DISPLAY)SET XXXX (TIME DISPLAY) Called station number flashes at calling station Series III Series E CB XXXX (TIME DISPLAY)CALLBACK XXXX (TIME DISPLAY)