NEC Neax 2000 Ivs Wcs System Manual

ND-46248 (E) CHAPTER 4
Pag e 11 9
Revision 2.0
SYSTEM DATA PROGRAMMING
3.2 ZT Set Up
3.2.1 Initial Set Up of ZT
Do the following procedure to set up the ZT.
Note:When reinstalling the system after power down exceeding 8 hours, the System ID will be cleared. Re-
entry of the System ID must be required.
START
Assignment of ZT dataSee Section 3.1.
Call NTAC
G1, G2.
ZT Authorization
SYS ID AssignmentAssignment of
LVP Code
END
or Enter the 
LVP code
ZT AuthorizationNTAC LVP
Mat Worx 32
Please call NTAC (NECAM...

CHAPTER 4 ND-46248 (E)
Pag e 12 0
Revision 2.0
SYSTEM DATA PROGRAMMING
3.2.2 Setting Up of Additional ZT
Do the following procedure to add the ZT.
START
Assignment of ZT data
ZT Authorization
END
See Section 3.1.
See MAT mode MENU in COM04,
G2. ZT Authorization.
Please call NTAC (NECAM National Technical Center)
for this data assignment. Action by Maintenance Person :
: 

ND-46248 (E) CHAPTER 4
Pag e 12 1
Revision 2.0
SYSTEM DATA PROGRAMMING
3.3 PS Data Assignment
Proceed with the following procedure after SYS ID Assignment and ZT Authorization by NTAC.
DESCRIPTION DATA
Assign a PS Station No. to the required virtual 
PS No.(1)
(2)Virtual PS No. (0001 ~ 0255)
X-XXXX: PS Station No. (X=0-9, *, #)
Assign a PS-ID.
(Primary PS Station only)
Note 1:Insert leading zeroes in the PS-
ID for a mzximum of nine digits.
For example, if PS ID is 1234,
enter 000001234 as the PS-ID....

CHAPTER 4 ND-46248 (E)
Page 122 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Service Restriction Class to each 
PS station.•
(1)
(2)YY=02 
X-XXXX: PS Station No.
XX
 XX
Service Restriction Class A 
(00-15 )
When providing Roaming Service, specify the 
Service Restriction Class for Roaming Service 
data down load.
Note 1:Assign the same Service
Restriction Class data to the PS
station number and the Virtual
LC Station number (see section
3.7.4) for Roaming...

ND-46248 (E) CHAPTER 4
Addendum-001 Page 123
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
When changing the PS operation data
If you change the PS operation data in this section already downloaded to a PS, repeat PS data download (CM1D 
YY=20 second data: 1).
DESCRIPTION DATA
Download the PS operation data to each PS by 
assigning the 2nd data 1.
Note 1:All steps for setting up ZTs and
all wiring must be successfully
completed and ZTs must be idle
before downloading PS
operation data.
Note 2:When a...

CHAPTER 4 ND-46248 (E)
Pag e 12 4
Revision 2.0
SYSTEM DATA PROGRAMMING
3.4 Virtual Line/Trunk Data Assignment
For Integrated Type/Adjunct Type2 (CCIS)
DESCRIPTION DATA
Assign a Virtual Line/Trunk Circuit No. to the 
required LEN.
Note 1:Be sure to assign the Station No.
to the Level 1 and Level 3.
Be sure to assign the Trunk No.
to the Level 0 and Level 2.
Note 2:The Virtual Line/Trunk Circuit
No. must be assigned from the
last LEN No. 0511.(1)
(2)LEN: (0511-0000)
X-XXXX: Virtual Station No.
D000-D255:...

ND-46248 (E) CHAPTER 4
Pag e 12 5
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the data for the Virtual Line/Trunk to 
the Trunk Route No. assigned by CM30 
YY=00.
(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)

(1)
(2)YY=00 (Kind of Route)
Trunk Route No. (00-63)
00: DDD
YY=01 (Type of Signal)
Trunk Route No. (00-63)
4: DTMF
YY=04 (Answer Signal Condition)
Trunk Route No. (00-63)
1: Answer Signal by Polarity Reversal
YY=05 (Release Signal Condition)
Trunk Route No. (00-63)
1...

CHAPTER 4 ND-46248 (E)
Pag e 12 6
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify a path between the Virtual Line and 
Trunk assigned by CM10.
Note:Combination must be as follows:
 Level 0 Trunk No. and Level 1
Station No.
 Level 2 Trunk No. and Level 3
Station No.
(1)
(2)YY=00
Block No. (000-169)
DXXX (Virtual Trunk No. 000-255)
+ + X-XXXX (Virtual Station No.)
Assign the Virtual Trunk to be seized on each 
PS station basis.
(1)
(2)YY=16
X-XXXX: PS Station No.
D000-D255: Virtual Trunk...

ND-46248 (E) CHAPTER 4
Pag e 12 7
Revision 2.0
SYSTEM DATA PROGRAMMING
The example of the data setting for the Virtual Line/Trunk is as follows:
LEN No. LEVEL CM10CM12 CM13 CM30
YY=00 YY=18 YY=00 YY=02 YY=03 YY=04 YY=05
0511LEVEL 
3201 1 0
0510LEVEL 
2D001ROUTE 
No.04 04PS 
Station 
No.
ex.)A201PS 
Station 
No.
ex.)A201
0509LEVEL 
1200 1 0
0508LEVEL 
0D000ROUTE
No.04 04PS 
Station 
No.
ex.)A200PS 
Station 
No.
ex.)A200
LEN No. LEVELCM35
YY=00 YY=01 YY=04 YY=05 YY=09 YY=20 YY=98
0511LEVEL 
3
0510LEVEL...

CHAPTER 4 ND-46248 (E)
Pag e 12 8
Revision 2.0
SYSTEM DATA PROGRAMMING
3.5 Trunk Data Assignment
For Adjunct Type1
DESCRIPTION DATA
Assign a Trunk No. to the required LEN. (1)
(2)LEN (0000-0511)
Trunk No. (D000-D255)
Assign the Trunk Route No. to the Trunk No.
(1)
(2)YY=00 (DP or DTMF)
Trunk No. (000-255)
Trunk Route No. (00-63)
Assign the data for terminating system.

(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
Trunk No. (000-255)
04: DIT
Assign the PS Station No. to be terminated by 
DIT.

(1)...