NEC Neax 2000 Ivs Wcs System Manual

ND-46248 (E) CHAPTER 4
Addendum-001 Page 157
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
3.7.4 Visitor PS Data Assignment
DESCRIPTION DATA
Execute System Data Memory All Clear of the
DBM (AP00) card.
The System Data Memory All Clear must be
done at the initial setup.
This data is valid when the DBM card is on-
line.•
(1)
(2)YYY=999
1 (All Clear)
CCC
Execute Work Memory All Clear of the DBM
card.
The Work Memory All Clear must be done be-
fore the system starts operating. All HLR,
VLR data is cleared...

CHAPTER 4 ND-46248 (E)
Page 158 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign the Trunk Route to be used for request-
ing the data of the Visitor PS against its Home
PBX.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=100-107 (Route Selection Pattern 
No. 00-07)
1-4: First-Fourth Selected Route
00-63: Q931a D Channel Trunk Route No.
NONE  : No Data
CCC: No Data Clear
Assign the Default restriction class for Visitor
PS.
Note:This data must be...

ND-46248 (E) CHAPTER 4
Pag e 15 9
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the telephone set type of Virtual LC 
for the Visitor PS as 10 PPS.
(1)
(2)YY=00
X-XXXX: Virtual LC Station No.
1: 10 PPS
Assign the Service Restriction Class of the 
Virtual LC for the Visitor PS.
Assign the different class to the Virtual LC for 
Visitor PSs from the station and Home PS of 
the PBX.
(1)
(2)YY=02
X-XXXX: Virtual LC Station No.
XXYY
XX: Service Restriction Class A
(00-15 )
YY: Service...

CHAPTER 4 ND-46248 (E)
Pag e 16 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each trunk number 
used for Virtual COT for the Visitor PS.
Make a separate route from other trunk routes.
(1)
(2)YY=00
Trunk No. (000-255)
Trunk Route No. (00-63)
Assign the terminating system to the Virtual 
COT as “Roaming Termination”.
(1)
(2)YY=02 (Day Mode)
YY=03 (Night Mode)
Trunk No. (000-255)
22: Roaming Termination
Assign trunk route data to the Virtual COT 
route number for the...

ND-46248 (E) CHAPTER 4
Addendum-001 Page 161
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Route Selection Pattern Number 
as “Pattern Number 0”, for all classes of the 
Trunk Restriction Class (01-06) sent from the 
Home PBX.
This data is valid when the DBM card is on-
line.
(1)
(2)YYY=208
01-06: Trunk Restriction Class sent from 
the Home PBX
00: Route Selection Pattern 0
Specify the Virtual COT Trunk route to be 
used for originating/terminating calls from/to 
the...

CHAPTER 4 ND-46248 (E)
Pag e 16 2
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Provide the Visitor PS with the capability to 
enter an Account Code, if required.
(1)
(2)YY=30
00-15 (Service Restriction Class A
assigned by CM12 YY=02)
0: Restricted
1 : Allowed
Specify the maximum number of Account 
Code.(1)
(2)10 (Max. Digits for Account Code)
01-16 : 01-16 digitsCM15
E
CM42
END 

ND-46248 (E) CHAPTER 4
Pag e 16 3
Revision 2.0
SYSTEM DATA PROGRAMMING
3.8 Maintenance Data Assignment
DESCRIPTION DATA
Assign the registration of fault information 
into Memory and the control of the external 
alarm.
(1)
(2)Y=2 
12:  ZT fault occurred (Not recovered)
2B:  ZT fault occurred
3B:  ZT fault recovered
0:  Registration of Fault Memory/No out-
put of External alarm
1:  Registration of Fault Memory
/External alarm is MN alarm
2:  Registration of Fault Memory
/External alarm is MJ alarm
NONE  :...

CHAPTER 4 ND-46248 (E)
Pag e 16 4
Revision 2.0
SYSTEM DATA PROGRAMMING
3.9 Maintenance Administration Terminal (MAT)
The figures below describe the installation for the WCS Maintenance Administration Terminal (MAT). For
more information about system-required equipment, system description and MAT Operation, refer to your MAT
Operation Guide.
3.9.1 Direct Connection
Figure 4-1    Cable Connection (Direct)
Table 4-1  MAT Cable (Direct)
DESCRIPTION QUANTITY REMARKS
MAT CA-Q 1/Sys RS-232C Cable, 13.1 ft. (4.0...

ND-46248 (E) CHAPTER 4
Pag e 16 5
Revision 2.0
SYSTEM DATA PROGRAMMING
3.9.2 Remote Connection
Remote connection is available via an internal modem in the MP or an external modem.
Remote Connection via Internal Modem
Figure 4-2    MAT Cable Connection (Remote Connection via Internal Modem)
Note 1:
The Installation Cable is connected to LTC0, LTC1, or LTC2 connector depending on the installed loc-
tion of the COT card.
Note 2:The MP to COT connection is made through internal switching of the Time...

CHAPTER 4 ND-46248 (E)
Pag e 16 6
Revision 2.0
SYSTEM DATA PROGRAMMING
4. DATA PROGRAMMING SHEETS
This section provides the sheets of WCS data, on a command basis. Complete the blank with data assigned. The
following symbol with the meaning indicated below is used within the data sheets.
: System Initialization
After data setting, system initialization is required by the SW1 switch on the MP card.
INITIAL