NEC Neax 2000 Ivs Wcs System Manual

ND-46248 (E) CHAPTER 3
Pag e 11 1
Revision 2.0
INSTALLATION
Figure 3-58    Example of Cable Connection via MDF for DTI
TO
PIM0
DTI
RECEIVE
SEND
TO CSU JP MDFLTC1
12
1
2
39 38 37 36 35 34 33 32 31
TB TA RB RA
RA
RB
TA
TB T0-31
32
33
34 RA
RB
TA
TB17
42
18
4317
42
18
43
17
18
19
20RA
TA42
43
44
45RB
TB42
43
44
4517
18
19
20RA
TA RB
TB LTC1 CONNECTOR
LTC (J) (P)
MDF CONNECTOR AP0
[LT10] 

CHAPTER 3 ND-46248 (E)
Pag e 11 2
Revision 2.0
This page is for your notes. 

ND-46248 (E) CHAPTER 4
Pag e 11 3
Revision 2.0
CHAPTER 4 SYSTEM DATA PROGRAMMING
1. GENERAL
This chapter describes the programming procedure for providing the WCS to the PBX.
2. SYSTEM DATA PROGRAMMING INFORMATION
In the programming procedure, the meaning of (1), (2) and markings are as follows.
(1) : 1st Data
(2) : 2nd Data
: Initial Data
With the system data clear command (CM00, CM01), the data with this marking is automatically
assigned for each command.
: System Initialization
After entering the...

CHAPTER 4 ND-46248 (E)
Pag e 11 4
Revision 2.0
SYSTEM DATA PROGRAMMING
3. PROGRAMMING PROCEDURE
Assign the system data related to the WCS, according to the following procedure.
For other system data related to the PBX, refer to the Command Manual, the Feature Programming Manual, and
the Office Data Programming Manual.
1. Initial set up of the system
Virtual Line/Trunk Data
Assignment
START
ZT Data Assignment
ZT Set Up
See Section 3.1.
PS Data Assignment
See Section 3.2.
See Section 3.3.
Adjunct System...

ND-46248 (E) CHAPTER 4
Addendum-001 Page 115
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
2. When changing the ZT data in service
When changing the ZT data in section 3.1 (CM10, CM06, CMAD, CMAE) in service, make busy of the
ZT is required. In this case, do the following procedure.
* To make busy the ZT in service, assign as follows:
CME5 Y=3
(1) ZT No. (000 ~ 255)
(2) 2 : Make busy after calls finished.
START
END
Change of ZT Data?
NO YES
Change of ZT Data
(CM10, CM06, CMAD, CMAE)
Make Busy of ZT...

CHAPTER 4 ND-46248 (E)
Page 115-1 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
3. When changing the PS operation data
If you change the PS operation data previously downloaded to a PS, repeat PS data download.
CM1D YY=20
(1) X-XXXX: PS Station No.
(2) 1
4. When replacing the PS
When replacing the PS with a new one, and assigning the same PS number to the new PS, it is required to
delete the PS number registered to the WCS by CM1C before downloading the new PS operation data.
CM1C
(1)...

ND-46248 (E) CHAPTER 4
Addendum-001 Page 115-2
MARCH, 1999 Revision 2.1
This page is for your notes. 

CHAPTER 4 ND-46248 (E)
Page 116 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
3.1 ZT Data Assignment
When changing the ZT data (CM10, CM06, CMAD, CMAE) in service, make busy of the ZT (CME5 Y=3-2)
is required. See the previous page.
DESCRIPTION DATA
Assign an AP number to the CSH card. 
The AP number must correspond to the value 
set by the SENSE switch on the CSH card.(1)
(2)Slot No. (04 ~ 15)
23: CSH (PN-SC03) card
Assign a ZT No. to the required LEN.
Note:The ZT No. must be assigned...

ND-46248 (E) CHAPTER 4
Addendum-001 Page 117
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the type of ZT
Note:After reassigning this data, the ZT
must be reset by either
unplugging it, then plugging it
back in or by Make Busy/Made
Idle with CME53.
(1)
(2)YY=19
ZT No. (000-255)
00: ZT II type (Mode 2)
15 : Previous ZT Type (Mode 1)
Assign a PAD data to each ZT, if required.
(1)
(2)YY=01/08/09/10 (Connecting Patterns)
ZT No. (000-255)
See the following Table:
T: Transmitter...

CHAPTER 4 ND-46248 (E)
Page 118 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
When providing Roaming Service, assign the 
Network ID.
(1)
(2)YY=42
00 (Network ID Assignment)
00000-65534: Network ID
NONE : Invalid (No Network ID)
Note:Network ID Method:
Network ID Method is one Method to operate multi-site roaming. A Roaming PS must
have two SYS-IDs on the Network ID Method. One is main SYS-ID for Home PBX and
the other is Network ID for Roaming Network. The Network ID is...