NEC Neax 2000 Ivs Wcs System Manual

ND-46248 (E) CHAPTER 3
Page 81
Revision 2.0
INSTALLATION
CAUTION
Battery Replacement Table and Battery Warnings
The label which shows battery replacement table and battery warnings is attached to the reverse side of Front
Cover for PIM, BATTM and PWRM.
During the battery installation process, the warning statements must be observed. When replacing batteries,
the battery replacement table should be observed in order to increase battery life and insure a safe operation.
25 ~ 30°C
2.0 ~ 2.5 (77 ~ 86°F)...

CHAPTER 3 ND-46248 (E) 
Pag e 82
Revision 2.0
INSTALLATION4.11.1 Internal Battery Connection
STEP  1:  Mount  th e t wo b atte ries  (1 2V  DC, 3. 0–3 .4 A H f o r  PW 86  c ard ) in to  e a ch  P IM  as s h ow n in  F ig u re  3-
3 5.
Figure 3-35    Internal Battery Mounting (1 of 2)
Note:
The two 2/12V batteries do not backup power feeding 2Ts, which can be backed up by adding 48V bat- 
tery. See Section 4.11.2.
FRONT
W 67 mm
DIMENSION OF BATTERY
BATTERY UNIT 
(2 
× 12VDC, 3.0 to 3.4AH)
(2.6 inch) L...

ND-46248 (E) CHAPTER 3Page 83
Revision 2.0
INSTALLATION
Figure 3-35  Internal Battery Mounting (2 of 2)
Note:
The two (2) 12V batteries do not backup power feeding ZTs, which can be backed up by adding 48V 
b atter y.  See  Se ction 4 .11.2 .
FRONT
W 34 mm DIMENSION OF BATTERY
BATTERY UNIT 
(2 
× 12V DC, 2.6AH)
(1.3 inch) L 178 mm(7.1 inch)
H 60 mm
(2.4 inch) PIM
Blue
Red
Pin # 4
Pin # 1

  NEAX1000 IVS
Recommended Battery 
GS type PX12026
Black 

CHAPTER 3 ND-46248 (E) 
Pag e 84
Revision 2.0
INSTALLATION
STEP 2:  Plug  the b atte ry ca ble  c onn ec tor  in to the  B ATT1  con nec tor  o n the  P W 86 ca rd as  sh ow n in  Fig ure  3-
3 6.
STEP  3:  Secu re  the  batt e rie s  and b atte ry c ab le u sing  t ie w raps  as  sh ow n  in  Figu re 3 -36 .
Figure 3-36    Internal Battery Connection
PLUG IN TO BATT 1 
CONNECTOR ON PZ-PW86
FRONT
TIE WRAP
PIM
BATTERY CABLE 

ND-46248 (E) CHAPTER 3Page 85
Revision 2.0
INSTALLATION
STEP 4: When the system is a multiple PIM configuration, plug the PWR CA-A into the BATT2 connector on the  PW 86  ca rd  as s how n in  Fig ure  3-37.
Figure 3-37    Internal Battery Connection for a Multiple PIM Configuration
PWR CA-A
BATT2 
BATT1
PW86
–+–+
PIM3
BATT2 
BATT1
PW86
–+–+
PIM2
BATT2 
BATT1
PW86
–+–+
PIM1
BATT2 
BATT1
PW86
–+–+
PIM0
BATTERY CABLE
BATT2 
BATT1
PW86
–+–+
PIM7
BATT2 
BATT1
PW86
–+–+
PIM6
BATT2 
BATT1
PW86
–+–+
PIM5
BATT2...

CHAPTER 3 ND-46248 (E)
Pag e 86
Revision 2.0
INSTALLATION
Figure 3-38    PWR CA-A
550 mm (21.7 inch)
PWR CA-A 

ND-46248 (E) CHAPTER 3
Addendum-001 Page 87
MARCH, 1999 Revision 2.1
INSTALLATION
4.11.2 Battery Connection in PWRM
When the system is equipped with one or two PW91 card, the battery for PW91 card can be mounted into the
Power Module (PWRM). When the system is equipped with more than two PW91 card, refer to Section 4.11.3.
Note:A 48V battery (4x12 VDC) is required to back up PW91 for ZT power feeding.
STEP 1: Connect the battery cables to the batteries as shown in Figure 3-39.
Figure 3-39    Battery...

CHAPTER 3 ND-46248 (E) 
Pag e 88
Revision 2.0
INSTALLATION
STEP 2:  Secu re  t he B atte ry Br ac k et   a nd   t o  th e  PW RM as  sh ow n  in  Figu re  3-40 .
STEP  3:  Mount  t he  batte ry u nit  ( 4 x12 VDC,  7A H  per un it)  i n to  the  P W RM as  sh ow n  in  Figu re  3-40 .
STEP  4:  Secu re  t he B atte ry Br ac k et  to  the  PW RM as  sh ow n  in  Figu re 3 -40 .
Figure 3-40    Battery Mounting into PWRM
12
3
BATTERY BRACKET 1BATTERY UNIT (4x12 VDC, 7AH)
BATTERY BRACKET 3
BATTERY BRACKET
2...

ND-46248 (E) CHAPTER 3Page 89
Revision 2.0
INSTALLATION
STEP  5:  Plug  the b atte ry ca ble  c onn ec tor  in to the  B ATT2  con nec tor  o n the  P W 91 ca rd as  sh ow n in  Fig ure  3-
4 1.
STEP  6:  Co nne ct  the PW91  ca rd s  to  each  o ther  us ing  the  P W R CA -A as  sh ow n  in  Figu re 3 -41 .
Figure 3-41    Battery Connection in PWRM
PWRM
PW91
BATT2 
BATT1PW91
BATT2 
BATT1
PWR CA-A BATTERY UNIT (48VDC, 7AH)
BATTERY CABLE 

CHAPTER 3 ND-46248 (E) 
Pag e 90
Revision 2.0
INSTALLATION4.11.3 Battery Connection in BATTM
1. For PW86 card (-24 V DC) 
STEP 1: Connect the battery cables to the batteries, and mount the battery units (2 ×12 V DC, 24AH per unit)
i n to t he Ba tt e ry  M odule  ( B ATTM)  as sh ow n  in  Figur es  3-42 and  3-4 3.
Figure 3-42    Battery Mounting into BATTM for PW86 Card
Recommended Batteries
GS Portalac PE12V 24ABI 
Yuasa NP24-12B
Specifications UL Listed 
12V DC, 24AH
Terminal:  bolt/nut type with...