NEC Neax 2000 Ivs Wcs System Manual

ND-46248 (E) CHAPTER 4
Pag e 14 7
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the order of LCR selection for the 
Route Pattern No. assigned by YYY=400-407.
(1)
(2)YYY=000-063
(Route Pattern No. 00-63) 
1-4: Order of LCR Selection 
1: 1st
2: 2nd
3: 3rd
4: 4th
XXX
 XX 
*a: 000-255 (LCR Pattern No. 000-255)
*b: 00-63 (Trunk Route No. 00-63) 
To delete the designated digit of an area code:
(1)
(2)YYY=500-755
153 (Designation of digit to be deleted)
00: No digits deleted 
01: First digit...

CHAPTER 4 ND-46248 (E)
Pag e 14 8
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the maximum number of digits to be 
dialed by the calling party.
The maximum number of digits including the 
area codes should be assigned to each area 
code. 
(1)
(2)Y=0-7 (Area Code Development Pattern No. 
0-7 assigned by CM8A, YYY=A00)
X-X...X (Area Code dialed, Max. 8 digits) 
01 : 1 digit 
24 : 24 digits 
79 : 79 digits 
B
CM85
END
||
|| 

ND-46248 (E) CHAPTER 4
Addendum-001 Page 149
MARCH, 1999 Revision 2.1
SYSTEM DATA PROGRAMMING
3.7.2 Q931a Digital Trunk Assignment
1. DTI Assignment
DESCRIPTION DATA
Assign an AP number to the DTI card.
The AP number assigned must coincide with 
the value set by the SENS switch on the DTI 
card.(1)
(2)AP No. (04-15)
09: DTI card
Assign the trunk number to each channel 
number on the DTI card.
Note:The system allocates time slots to
consecutive channels from
lowest to highest channel
number assigned. To...

CHAPTER 4 ND-46248 (E)
Pag e 15 0
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign a Trunk Route to each trunk number 
used for voice channel (B channel), and also to 
signaling channel (D channel). Make a sepa-
rate route for B channels and D channels.
Note:DTI route must be separated
from analog trunk 
routes

(1)
(2)YY=00
B Channel, D channel Trunk No. (000-255) 
assigned by CM07 YY=01
Trunk Route No. (00-63)
Assign the terminating system to each incom-
ing trunk used for voice channel,...

ND-46248 (E) CHAPTER 4
Pag e 15 1
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Assign trunk route data to each channel trunk 
route number assigned by CM30 YY=00.
(1)
(2)YY=00 (Kind of Trunk Route)
B Channel, D Channel Route No. (00-63)
04: Tie Line

(1)
(2)YY=01 (Dialing Signal Type)
B Channel Route No. (00-63)
7 : Call Termination; DP/DTMF
Call Origination; DTMF

(1)
(2)YY=04 (Answer Signal from Distant Of-
fice)
B Channel Route No. (00-63)
2 : Answer signal arrives.
7 : Answer signal does...

CHAPTER 4 ND-46248 (E)
Pag e 15 2
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
(1)
(2)YY=19
B Channel Route No. (00-63)
0:
1: Programmable PAD 
2: (See CM42)
3:
4:
5: Fixed PAD
6: (See left table)
7:
When using the programmable PAD (CM35 
YY=19, 2nd Data=0-3), assign the PAD data.(1)
(2)50-65
00-15
T/R: Transmitter PAD/Receiver PAD
+: Gain
–: Loss
CM35
B
CM42
END
CONNECTION 
PAT T E R N SPAD DATA OF DTI [dB]
DATA
=4 (T/
R)DATA
=5 (T/
R)DATA
=6...

ND-46248 (E) CHAPTER 4
Pag e 15 3
Revision 2.0
SYSTEM DATA PROGRAMMING
2. DCH Assignment
DESCRIPTION DATA
Assign an AP number to the DCH card (PN-
SC01).
The AP number assigned must coincide with 
the value set by the SENS switch on the PN-
SC01 card.(1)
(2)AP No. (04-15)
35: DCH for Roaming
Assign the DCH number to the AP number of 
DCH assigned by CM05.
(1)
(2)YY=08
DCH No. (0-4)
XX: AP No. assigned by CM05
Execute CM35 YY=90 for the B channel route 
and D channel route.
(1)
(2)YY=90 (Special...

CHAPTER 4 ND-46248 (E)
Page 154 Addendum-001
Revision 2.1 MARCH, 1999
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the LAPD Mode of the D channel 
route as “Network Mode” or “User Mode”. 
This data must be set differently between the 
opposite DTIs. When the opposite office is a 
master office, set this data to 1 (User Mode), 
and when the opposite office is a slave office, 
set this data to 0 (Network Mode). 
(1)
(2)YYY=113 (LAPD Mode)
D Channel Route No. (00-63)
0: Network Mode
1: User Mode
Assign...

ND-46248 (E) CHAPTER 4
Pag e 15 5
Revision 2.0
SYSTEM DATA PROGRAMMING
3.7.3 Home PS Data Assignment
DESCRIPTION DATA
Assign an AP number to the DBM (Data Base 
Module) card (PN-AP00).
The AP number must be coincide with the val-
ue set by SENSE switch of the card.(1)
(2)AP No. (04-15)
34: DBM (AP00)
Assign the Trunk Restriction Class for Home 
PS. This data is sent to the visitor PBX when 
the PS is roaming.
Note:When the location registration of
a Visitor PS is executed, the
Trunk Restriction Class...

CHAPTER 4 ND-46248 (E)
Pag e 15 6
Revision 2.0
SYSTEM DATA PROGRAMMING
DESCRIPTION DATA
Specify the Service Restriction Class for 
Roaming Service download.
Note:Assign the same Service Restric-
tion Class data to the Virtual LC
Station number and the PS Sta-
tion number (See Section 3.3) for
Roaming Service.
(1)
(2)YYY=117
00-15: Service Restriction Class A 
Assigned by CM12 YY=02
0 : Allowed
1 : Restricted
Specify whether the Home PBX Numbering 
Plan is the Open Numbering System or Closed 
Numbering...