NEC Neax 2000 Ivs Installation Procedure Manual

							CHAPTER 3 ND-45492 (E)
Pag e 6 4
Revision 2.0
Figure 004-4  Switch Setting on the SN610/611/615 ATTCON (2 of 2)
NAP 200-004
Sheet 5/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
D
S
C SWITCH
• Set the switch according to the type of headset/handset connected.
C: Carbon Type Handset/Headset
S: SUPRA Headset
D: D
term Type Handset
• Replace the directory and access panel. 
						

							ND-45492 (E) CHAPTER 3
Page 65
Revision 2.0
(4) Plug the line cord into the modular jack located at the bottom of the console.  For the MDF cross connection
for the SN610 ATTCON, refer to NAP- 200-007 (Figure 007-23).
Figure 004-5  Cable Connection to the SN610 ATTCON
NAP 200-004
Sheet 6/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
LINE CORD
PBX
PN-
2DLCC 2P MDF
MODULAR
TERMINAL
SN610 ATTCON2P 2P 
						

							CHAPTER 3 ND-45492 (E)
Pag e 6 6
Revision 2.0
3. Installation of SN716 DESKCON
(1) Screw the handset support onto the bottom of the console, if required.
Figure 004-6  Mounting of the Handset Support to the SN716 DESKCON
The handset support bracket is reversible to mount on either side of the SN716 DeskCon. To mount the sup-
port unit on the right hand side of the DeskCon, reverse the mounting bracket on the handset support unit
(two screws). Then attach the handset support with three screws on the right side of the DeskCon.
NAP 200-004
Sheet 7/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required  
						

							ND-45492 (E) CHAPTER 3
Page 67
Revision 2.0
(2) Plug the headset into the modular jack (H/S 0 or H/S 1) located at the bottom of the console, if required.
Figure 004-7  Headset Installation for the SN716 DESKCON
NAP 200-004
Sheet 8/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
H/S 1HAND
H/S 0 
						

							CHAPTER 3 ND-45492 (E)
Pag e 6 8
Revision 2.0
(3) Plug the line cord into the modular jack (LINE) located at the bottom of the console. For the MDF cross
connection fot the SN716 DESKCON, refer to NAP-200-007 (Figure 007-24, 007-24).
Figure 004-8  Cable Connection to the SN716 DESKCON
NAP 200-004
Sheet 9/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
PBX
DLC 1P MDF
MODULAR
TERMINAL
SN716 DESKCON3P 3P
PW00
2P
LINE CORD
PAGE REC
LINE 
						

							ND-45492 (E) CHAPTER 3
Page 69
Revision 2.0
(4) When using an AC-DC ADAPTER for power supply, plug the AC-DC ADAPTER into the “12V~24VDC”
terminal located at the rear of the console. This adapter is the same as the Dterm Series E AC-DC adapter.
Figure 004-9  AC-DC ADAPTER Connection to the SN716 DESKCON
NAP 200-004
Sheet 10/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
AC/DC ADAPTER
Note:AC-DC Adapter is only required when the PW00 card is not used. 
						

							CHAPTER 3 ND-45492 (E)
Pag e 7 0
Revision 2.0
(5) When using the PW00 card for power supply, provide the PW00 card according to the following procedure.
(a) Mount the PW00 card into the LT01-LT15 or AP6 slot.
Figure 004-10  Mounting PW00 Card into PIM
NAP 200-004
Sheet 11/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
BUILT-IN BATTERY
Note:The PW00 card occupies the adjoining left side (smaller number) slot because of its two-stories
structure.
PIM
P
W
R
LT00LT01LT02LT03LT04LT05LT06LT07LT08LT09LT10/AP0LT11/AP1LT12/AP2LT13/AP3LT14/AP4LT15/AP5FP/AP6MP/FP/AP7BUS/AP8
PW00 
						

							ND-45492 (E) CHAPTER 3
Page 71
Revision 2.0
(b) Connect the PW00 card and SN716 DESKCON using installation cable as shown in Figure 004-11
and Figure 007-24 (1 of 1 and 1 of 2).
Figure 004-11  PW00 Card connection to the SN716 DESKCON
NAP 200-004
Sheet 12/12
Installation of Peripheral Equipment
AT TENTION
Contents
Static Sensitive
Handling
Precautions Required 
PIMPWR0CCONN Connector
PW00
TO DESKCONPWR1PW86 
						

							CHAPTER 3 ND-45492 (E)
Page 72 Addendum-001
Revision 2.1 JANUARY, 1999
1. Battery Connection
WARNING:Turn off AC power before connecting batteries.
NAP 200-005
Sheet 1/7
Connection of Battery
Recommended Battery
Internal Battery: YUASA
MATSUSHITAtype NPH-3.2-12
type LCR-12V3.4NE
External Battery:
(BATTM)YUASA
MATSUSHITAtype NP-24-12B
type LCL-12V-24
If battery terminals (+, –) contact with the module while connecting the battery cable to the PZ-PW86 card,
the PZ-PW86 card or the BWB may be shorted. Therefore, the installer must perform work in accordance with
the following steps when mounting or removing the batteries.
(1) When mounting batteries:
(a) Connect the battery cable to the batteries.
(b) Mount the batteries into the appointed position of the PIM or the BATTM.
(c) Connect the battery cable to the PZ-PW86 card.
(2) When removing batteries:
(a) Disconnect the battery cable from the PZ-PW86 card.
(b) Remove the batteries from the PIM or the BATTM.
CAUTION 
						

							ND-45492 (E) CHAPTER 3
Page 73
Revision 2.0
NAP 200-005
Sheet 2/7
Connection of Battery
CAUTION
Battery Replacement Table and Battery Warnings
The label which shows battery replacement table and battery warnings is attached to the reverse side of Front
Cover for PIM and BATTM.
During the battery installation process, the warning statements must be observed. When replacing batteries, the
battery replacement table should be observed to increase battery life and ensure a safe operation.
• ELECTROLYTE LEAKAGE OR OTHER HAZARDS MAY RE-
SULT IF THE BATTERY IS NOT REPLACED IN ACCOR-
DANCE WITH THE SPECIFIED INTERVALS.
AMBIENT
TEMPERATURE25°C
(77°F)25°C ~ 30°C
(77°F ~ 86°F)30°C ~ 40°C
(86°F ~ 104°F)
REPLAC EMENT 
INTERVAL2.5 ~  3
YEARS2.0 ~ 2.5
YEARS1.5 ~ 2.0
YEARS
FRONT COVER
PIM/BATTMLABEL
TO PREVENT INJURY AND SKIN BURN, PAY 
ATTENTION TO THE FOLLOWING.
• DO NOT STRIKE A MATCH OR CAUSE A SPARK IN VI-
CINITY OF BATTERY.
• PLACE THE EQUIPMENT IN A WELL VENTILATED AR-
EA.
• DO NOT SHORT.
• REPLACE BATTERY ONLY AFTER BATTERY GASES 
HAVE BEEN DISPERSED.CAUTION
BATTERY REPLACEMENT TABLE
INSTALLATION DATE:
,.