NEC Neax 2000 Ivs Installation Procedure Manual
Here you can view all the pages of manual NEC Neax 2000 Ivs Installation Procedure Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 51
CHAPTER 3 ND-45492 (E) Pag e 3 4 Revision 2.0 (9) Confirm the connection of the PWR CNT CA-A and power output cables as shown in Figure 003-10 (These cables are pre-installed). Figure 003-10 Cable Connection between the PZ-PW86 and the BWB NAP 200-003 Sheet 12/37 Installation of Main Equipment LTC CONNECTOR AREA PIM BWB (Back Wiring Board)PZ-PW86 PWR0B PWR0A RS PWR1 PWR CNT CA-A POWER OUTPUT CABLE (CR,E) POWER OUTPUT CABLE (+5V, -27V, E)CARD SLOT AREA
Page 52
ND-45492 (E) CHAPTER 3 Page 35 Revision 2.0 (10) AC CORD-B and AC Power Cable Wiring (a) The AC CORD-B and the AC Power Cable Wiring to the FG, NEUTRAL and LINE terminals inside the BASE are shown in Figure 003-11 (for details of wiring to the terminals, see Figure 003-12). Figure 003-11 AC CORD-B and AC Power Cable Wiring NAP 200-003 Sheet 13/37 Installation of Main Equipment TO GROUND TERMINAL FRONTSEE FIGURE 003-12AC CORD-B 3P AC POWER CABLE PIM PIM BASE
Page 53
CHAPTER 3 ND-45492 (E) Pag e 3 6 Revision 2.0 (b) Secure the AC CORD-B cables to the FG, NEUTRAL and LINE terminals as shown in Figure 003- 12. The 3P AC Power Cable and the FG Cable are pre-installed with the BASE. Figure 003-12 Screwing the AC CORD-B to the Terminals NAP 200-003 Sheet 14/37 Installation of Main Equipment FG NEUTRAL LINE BASE 3P AC POWER CABLE TO 120/240 V AC SOURCE POWER AC POWER KNOCK OUT HOLE (PROVIDED WITH BASE) FG CABLE (PROVIDED WITH BASE) PIMAC CORD-B TO PZ-PW86 IN PIM...
Page 54
ND-45492 (E) CHAPTER 3 Page 37 Revision 2.0 (c) When the system is a two-frame configuration, the 3P AC Power Cable of the left side frame can go through the BASE of the right side frame, as shown in Figure 003-12. Figure 003-13 AC Power Cable Wiring for Two-Frame Configuration NAP 200-003 Sheet 15/37 Installation of Main Equipment FGNEUTRALLINEFGNEUTRALLINE 3P AC POWER CABLE TO 120/240 V AC SOURCE POWER SUPPLEMENTARY GROUND (TO COLD WATER PIPE, ETC.)
Page 55
CHAPTER 3 ND-45492 (E) Pag e 3 8 Revision 2.0 (11) When the system is a multiple-PIM configuration, connect the PZ-PW86 Cards to each other using PWR CA-A cables, as shown in Figure 003-14 and Figure 003-15. Figure 003-14 PWR CA-A NAP 200-003 Sheet 16/37 Installation of Main Equipment 550mm (21.7 inch) PWR CA-A
Page 56
ND-45492 (E) CHAPTER 3 Page 39 Revision 2.0 (a) When using an External Battery or the BATTM Figure 003-15 Connection of PWR CA-A Cables (1 of 2) NAP 200-003 Sheet 17/37 Installation of Main Equipment PIM7 PIM6 PIM5 PIM4 PIM3 PIM2 PIM1 PIM0PWR CA-APZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 TO BATTERYPZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 TO BATTERY PWR CA-A Note:For details of battery connection, see NAP- 200-005. PWR CA-A PWR...
Page 57
CHAPTER 3 ND-45492 (E) Pag e 4 0 Revision 2.0 (b) When using an Internal Battery Figure 003-15 Connection of PWR CA-A Cables (2 of 2) NAP 200-003 Sheet 18/37 Installation of Main Equipment PIM7 PIM6 PIM5 PIM4 PIM3 PIM2 PIM1 PIM0PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 PZ-PW86 BATT2 BATT1 TO BATTERY PWR CA-A TO BATTERY TO BATTERY PWR CA-A TO BATTERY TO BATTERY PWR CA-A TO BATTERY TO BATTERY PWR CA-A TO...
Page 58
ND-45492 (E) CHAPTER 3 Page 41 Revision 2.0 (12) When the system is a multiple-PIM configuration, mount the PN-BS00 Card in the BUS slot of PIM0. Also, mount the PN-BS01 Card in each BUS slot of PIM1 through PIM7. When the system is a single PIM configuration, neither PN-BS00 nor PN-BS01 is needed. Figure 003-16 Mounting of the BUS Cards NAP 200-003 Sheet 19/37 Installation of Main Equipment B S 0 1 B S 0 1 B S 0 1 B S 0 0 B S 0 1 B S 0 1 B S 0 1 B S 0 1 PIM3 PIM2 PIM1 PIM0PIM7 PIM6 PIM5 PIM4 BUS SLOT
Page 59
CHAPTER 3 ND-45492 (E) Pag e 4 2 Revision 2.0 (13) When the system is a multiple-PIM configuration, connect all the BUS Cards (PN-BS00/PN-BS01) to each other using BUS cables, as shown in Figure 003-17 and Figure 003-18. Figure 003-17 BUS Cable NAP 200-003 Sheet 20/37 Installation of Main Equipment 700mm (27.6 inch) 48-TW-0.7 CONN CA
Page 60
ND-45492 (E) CHAPTER 3 Page 43 Revision 2.0 Figure 003-18 Connection of the BUS Cables NAP 200-003 Sheet 21/37 Installation of Main Equipment PIM7 PIM6 PIM5 PIM4 PIM3 PIM2 PIM1 PIM0BS01 CN2 CN1 CN2 CN1 CN2 CN1 CN2 CN1BS01 CN2 CN1 CN2 CN1 CN2 CN1 CN2 CN1 48-TW-0.7 CONN CA BS01 BS01 BS00BS01 BS01 BS01