NEC Neax 2000 Ivs Installation Procedure Manual

LIST OF TABLES ND-45492 (E)
Pag e v i
Revision 2.0
LIST OF TABLES
Table TitlePag e
Table 2-1 Description of Symbols in Trunking Diagram . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  4
Table 3-1 Procedure for Unplugging/Plugging Circuit Cards . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14
Table 003-1 Recommended Fasteners  . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .  46
Table 006-1...

ND-45492 (E) SAFETY CONSIDERATIONS
Page vii
Revision 2.0
SAFETY CONSIDERATIONS
IMPORTANT — SAVE THESE INSTRUCTIONS
(1) Never install telephone wiring during a lightning storm.
(2) Never install telephone jacks in wet locations unless the jack is specifically designed for wet loca-
tions.
(3) Never touch uninsulated telephone wires or terminals unless the telephone line has been discon-
nected at the network interface.
(4) Use caution when installing or moving telephone lines.
When using your telephone...

SAFETY CONSIDERATIONS ND-45492 (E)
Pag e v iii
Revision 2.0
shock.
(15) Never push objects of any kind into this product through cabinet slots as they may touch danger-
ous voltage points or shor t out parts that could result in a risk of fire or electric shock. Never spill
liquid of any kind on the product.
(16) To reduce the risk of electric shock, do not disassemble this product, but take it to a qualified ser-
viceman when some service or repair work is required. Opening or removing covers may...

ND-45492 (E) REGULATORY INFORMATION
Page ix
Revision 2.0
REGULATORY INFORMATION
1. Regulatory Requirements
The Federal Communications Commission (FCC) has established rules that permit the NEAX2000 IVS to be
directly connected to the telephone network.  A jack is provided on party lines or coin lines.
The telephone company may make changes in its technical operations and procedures. If such changes affect
the compatibility or use of the NEAX2000 IVS, the telephone company is required to give adequate...

REGULATORY INFORMATION ND-45492 (E)
Pag e x
Revision 2.0
NOTE:  Limitations on features exist if the system is registered as a KF system. Refer to Features and Specifi-
cations for details.
3.2 Service Requirements
In the event of equipment malfunction, all repairs will be performed by NEC or an authorized distributor of
NEC. It is the responsibility of users requiring service to report the need for service to NEC or to one of their
authorized distributors.
If the equipment causes harm to the telephone...

ND-45492 (E) REGULATORY INFORMATION
Page xi
Revision 2.0
• Routed to a recorded announcement that can be administered by the CPE user
• Routed to a dial prompt
(b) This equipment returns answer supervision on all DID calls forwarded to the PSTN.  Permissible ex-
ceptions are:
• A call is unanswered
• A busy tone is received
• A reorder tone is received.
EQUAL ACCESS REQUIREMENTS
This equipment is capable of providing users access to interstate providers of operator services through the use
of access...

REGULATORY INFORMATION ND-45492 (E)
Pag e x ii
Revision 2.0
NOTICE: The Industry Canada label identifies certified equipment. The certification means that the equipment
meets certain telecommunications network protective operational and safety requirements. The department does
not guarantee the equipment will operate to the user’s satisfaction.
Before installing the equipment, users should ensure that it is permissible to be connected to the facilities of the
local telecommunications company. The...

ND -4 5492 ( E)  CHAPTER 1
CHAPTER 1  INTRODUC TION
C IRCUIT  CARD  MAN UAL
M AINTEN ANCE  MAN UAL
COM MAND MAN UA L
SYS TEM  D ATA S HEET
CIRCUIT CAR D DESCR IPTION
D ESCRIP TION 

CHAPTER 1 ND-45492 (E)
Pag e 2
Revision 2.0
3. HOW TO FOLLOW THIS MANUAL
The Installation Procedure is shown by means of flowcharts with NEC Action Procedure (NAP) numbers.  The
details of each step are described in the NAPs.
3.1 SCOPE OF INSTALLATION PROCEDURES
This manual covers the installation shown in Figure 1-2.
Figure 1-2  Scope of Installation Works
NAP- 200-003: 
 INSTALLATION OF MAIN EQUIPMENT
NAP- 200-008: 
 MOUNTING OF CIRCUIT CARDSNAP- 200-004: 
 INSTALLATION OF 
 PERIPHERAL EQUIPMENT
SN610...

ND-45492 (E) CHAPTER 2
Page 3
Revision 2.0
CHAPTER 2 GENERAL INFORMATION
1. TRUNKING DIAGRAM
A typical trunking diagram for the PBX is shown in Figure 2-1.
Figure 2-1  PBX Trunking Diagram
MODEM
Note 1:An external Modem is not required when the Built-In Modem on the MP is used.
Note 2:The equipment marked with (*) is provided by the customer.
Note 3:The MP functions marked with (**) are included in the PN-CP03 card only.
4W E&M
2W E&M
RS 232C
V. 1 1
TCP/IP
V. 1 1
RS-232C
RS 232C
LONG LINE STATION
SINGLE...