NEC Mcu 5000a Multipoint Control Unit Equipment Manual
Here you can view all the pages of manual NEC Mcu 5000a Multipoint Control Unit Equipment Manual. The NEC manuals for Communications System are available online for free. You can easily download all the documents as PDF.
Page 331
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-038 MBE MESSAGE (VIDEO) CAPABILITY SETTING TERMINAL CAPABILITY RELATED SUMMARY: Set the expansion video capability of connecting CODEC (VL 5000). STEP PROCEDURE Note: Use the MBE message (video) capability with the factory shipment value (04H 00H ). If change is necessary for any reason, follow the steps described below. 1 Enter the following command. SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿ ni: System parameter...
Page 332
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-038 MCU 5000A Multipoint Control Unit MBE MESSAGE (VIDEO) CAPABILITY SETTING TERMINAL CAPABILITY RELATED STEP PROCEDURE SYSTEM PARAMETER MBE MESSAGE (VIDEO) CAPABILITY ADDRESS 11 D HADDRESS 11 C H 00H 00H OFF 00H 01H PTY is ON. 00H 02H PTY + FULL are ON. 00H 04H PTY + FULL + VSP are ON. Note: PTY detects a parity error and performs Demand Refresh on its occurrence. FULL: NTSC full resolution mode VSP: dual screen multiplex mode 2 Verify that the normal...
Page 333
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-039 AUDIO MODE SETTING TERMINAL MODE RELATED SUMMARY: Set audio mode. If all the terminal CODECs (VL 5000s) are equipped with SB- ADPCM audio CODEC (7 kHz band) features, set the audio mode to “G.722 mode 2 (P×64k network)” or “G.722 mode 3 (p×56k network)”. If not, set it to “µ -LAW and OF” and refrain from setting other values. STEP PROCEDURE 1 Enter the following command. SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿...
Page 334
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-039 MCU 5000A Multipoint Control Unit AUDIO MODE SETTING TERMINAL MODE RELATED STEP PROCEDURE SYSTEM PARAMETER AUDIO MODE CAPABILITY ADDRESS 123HADDRESS 122HADDRESS 121HADDRESS 120H 00H 00H 00H 04Hm-law, OU is ON. 00H 00H 00H 08Hm-law, OF (u7) is ON. 00H 00H 00H 10H G.722 mode 1 is ON. 00H 00H 00H 20H G.722 mode 2 is ON. 00H 00H 00H 40H G.722 mode 3 is ON. 00H 04H 00H 00Hm-law, OF (u6) is ON. 40H 00H 00H 00H Audio OFF, U is ON. 80H 00H 00H 00H Audio OFF, F...
Page 335
![Page 335
NECA 340-414-220 Revision 2.0 Page 1 of 4
MCU 5000A Multipoint Control Unit SPR-040
TRANSFER RATE MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Set the transfer rate for terminal.
STEP PROCEDURE
Note:
If rate is specified when setting up the multipoint teleconference by MCON or ECON
command, the MCON or ECON command specified rate is set.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter address124H
and 127H
[1] Addresses (hexadecimal values) on setting the...](http://img.usermanuals.tech/thumb/54/84243/w300_nec-mcu-5000a-equipment-manual_d-334.png "Page 335
NECA 340-414-220 Revision 2.0 Page 1 of 4
MCU 5000A Multipoint Control Unit SPR-040
TRANSFER RATE MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Set the transfer rate for terminal.
STEP PROCEDURE
Note:
If rate is specified when setting up the multipoint teleconference by MCON or ECON
command, the MCON or ECON command specified rate is set.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter address124H
and 127H
[1] Addresses (hexadecimal values) on setting the...")
NECA 340-414-220 Revision 2.0 Page 1 of 4 MCU 5000A Multipoint Control Unit SPR-040 TRANSFER RATE MODE SETTING TERMINAL MODE RELATED SUMMARY: Set the transfer rate for terminal. STEP PROCEDURE Note: If rate is specified when setting up the multipoint teleconference by MCON or ECON command, the MCON or ECON command specified rate is set. 1 Enter the following command. SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿ ni: System parameter address124H and 127H [1] Addresses (hexadecimal values) on setting the...
Page 336
![Page 336
Page 2 of 4 NECA 340-414-220 Revision 2.0
SPR-040 MCU 5000A Multipoint Control Unit
TRANSFER RATE MODE SETTING
TERMINAL MODE RELATED
STEP PROCEDURE
x
i:
System parameter values See below:
[1] System parameter values on setting the transfer rate mode for the addresses 124H to
127H.
The factory shipment value for the system parameter is 00H 02H 00H 00H
.
SYSTEM PARAMETER
Transfer rate mode
ADDRESS
127HADDRESS
126HADDRESS
125HADDRESS
124H
00H 00H 00H 01H 64 kb/s is ON.
00H 00H 00H 02H 64 kb/s x 2 is ON....](http://img.usermanuals.tech/thumb/54/84243/w300_nec-mcu-5000a-equipment-manual_d-335.png "Page 336
Page 2 of 4 NECA 340-414-220 Revision 2.0
SPR-040 MCU 5000A Multipoint Control Unit
TRANSFER RATE MODE SETTING
TERMINAL MODE RELATED
STEP PROCEDURE
x
i:
System parameter values See below:
[1] System parameter values on setting the transfer rate mode for the addresses 124H to
127H.
The factory shipment value for the system parameter is 00H 02H 00H 00H
.
SYSTEM PARAMETER
Transfer rate mode
ADDRESS
127HADDRESS
126HADDRESS
125HADDRESS
124H
00H 00H 00H 01H 64 kb/s is ON.
00H 00H 00H 02H 64 kb/s x 2 is ON....")
Page 2 of 4 NECA 340-414-220 Revision 2.0 SPR-040 MCU 5000A Multipoint Control Unit TRANSFER RATE MODE SETTING TERMINAL MODE RELATED STEP PROCEDURE x i: System parameter values See below: [1] System parameter values on setting the transfer rate mode for the addresses 124H to 127H. The factory shipment value for the system parameter is 00H 02H 00H 00H . SYSTEM PARAMETER Transfer rate mode ADDRESS 127HADDRESS 126HADDRESS 125HADDRESS 124H 00H 00H 00H 01H 64 kb/s is ON. 00H 00H 00H 02H 64 kb/s x 2 is ON....
Page 337
NECA 340-414-220 Revision 2.0 Page 3 of 4 MCU 5000A Multipoint Control Unit SPR-040 TRANSFER RATE MODE SETTING TERMINAL MODE RELATED STEP PROCEDURE Transfer Rate Mode (+124H ~ 127H) b7 b6b5 b4 b3 b2 b1 b0 b0 : 64 kbps (T1/RS422/INF-H0) b1 : 64 x 2 kbps (T1/RS422/INS-H0)Default = 00H +124H00 0 fixed0 fixed 0 fixed0 fixed 0 0 b6 : 128 kbps (T1/RS422) b7 : 192 kbps (T1/RS422) b7 b6b5 b4 b3 b2 b1 b0 b0 : 256 kbps (T1/RS422) b1 : 384 kbps...
Page 338
Page 4 of 4 NECA 340-414-220 Revision 2.0 SPR-040 MCU 5000A Multipoint Control Unit This page is for your notes.
Page 339
![Page 339
NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-041
VIDEO MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Specify whether video mode is set or not.
STEP PROCEDURE
Note:
Use the factory shipment value (08H 00H
) in setting the video mode as a general rule. If
change is necessary for any reason, follow the steps described below.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter address128H
and 129H
[1] Addresses (hexadecimal...](http://img.usermanuals.tech/thumb/54/84243/w300_nec-mcu-5000a-equipment-manual_d-338.png "Page 339
NECA 340-414-220 Revision 2.0 Page 1 of 2
MCU 5000A Multipoint Control Unit SPR-041
VIDEO MODE SETTING
TERMINAL MODE RELATED
SUMMARY:
Specify whether video mode is set or not.
STEP PROCEDURE
Note:
Use the factory shipment value (08H 00H
) in setting the video mode as a general rule. If
change is necessary for any reason, follow the steps described below.
1 Enter the following command.
SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿
ni:
System parameter address128H
and 129H
[1] Addresses (hexadecimal...")
NECA 340-414-220 Revision 2.0 Page 1 of 2 MCU 5000A Multipoint Control Unit SPR-041 VIDEO MODE SETTING TERMINAL MODE RELATED SUMMARY: Specify whether video mode is set or not. STEP PROCEDURE Note: Use the factory shipment value (08H 00H ) in setting the video mode as a general rule. If change is necessary for any reason, follow the steps described below. 1 Enter the following command. SSPR__ n1 = x1 __n2 = x2 __ … ni = xi … ¿ ni: System parameter address128H and 129H [1] Addresses (hexadecimal...
Page 340
Page 2 of 2 NECA 340-414-220 Revision 2.0 SPR-041 MCU 5000A Multipoint Control Unit VIDEO MODE SETTING TERMINAL MODE RELATED STEP PROCEDURE 2 Verify that the normal response is displayed with “OK ”. If YES , go to Step 3 . If NO , go to Step 1 . 3 End of procedure.