NEC Dsx 34b Manual

Tandem Calls / Unsupervised Conference
DSX Software ManualFeatures◆341
Features
Tandem Calls / Unsupervised Conference
Description
Tandem Calls allows an extension user to join two outside callers in a line-to-line conference. The extension 
user can then drop out of the call, leaving the lines in an Unsupervised Conference. The extension user that 
established the Conference is not part of the conversation. The Conference continues until either outside 
party hangs up.
Tandem Calls uses a Conference...

Tandem Calls / Unsupervised Conference
342◆Features DSX Software Manual
Other Related Features
Features
Forced Line Disconnect  (page 182)
An extension user can end an Unsupervised Conference by using Forced Line Disconnect on one of 
the lines in the tandem call.
Single Line Telephones  (page 305)
Tandem Calling is available at Single Line extensions.
The following features also allow different types of multiple party calls: -Barge In (Intrusion)  (page 36)
- Conference  (page 89)
- Group Listen  (page...

Tandem Calls / Unsupervised Conference
DSX Software ManualFeatures◆343
Features
Barging in on a Tandem CallIn these instructions:[Super Display Soft Key]
[Keyset Soft Key]
To Barge In on a Tandem Call:
1.
Do one of the following.
a.Press the line key for the busy line.
b.Press INTERCOM and dial the line’s Direct Line Access code (e.g., 101 for line 1).
• See  Direct Line Access  (page 115) for more.
2.Dial 4.
• You hear two beeps and you join the Tandem Call.
To place a Tandem Call on Hold (after...

Tie Lines
344◆Features DSX Software Manual
Tie Lines
Description
Tie lines directly link a local DSX-80/160 telephone system with one or m\
ore remote DSX-80/160 systems. 
The link is independent of the telcos switched network. When a local system user seizes a tie line, they hear 
Intercom dial tone from the remote system. The user can then use many of the features normally available to 
the remote system’s single line telephones, including:
❥Dialing Intercom extensions in the remote system.
❥Using the...

Tie Lines
DSX Software ManualFeatures◆345
Features
1.To restrict feature access:
- In  3102-01: Line Class of Service  (page 813), check the tie line’s Class of Service level.
- In  14xx-COS (Class of Service)  (page 628), restrict Class of Service options as required.
2.To restrict outgoing dialing:
- In  3102-02: Line Toll Level  (page 813), assign a Toll Level to the tie line.
- In  35xx-Toll Restriction  (page 839), set up dialing restrictions as required.
Other Related Features
Features
Direct...

Tie Lines
346◆Features DSX Software Manual
Operation
Call Waiting / Camp-On
1.
Access the tie line and call busy extension.
2.Dial 2 but do not hang up.
• If you hang up, the system converts your Camp-On to a Callback.
3.Speak to your co-worker when they answer their Camp-On ring.
Central Of fice Calls, Placing
1.
Access the tie line.
2.Do one of the following.
a.For Direct Line Access:
i.Dial 1 followed by the line number (e.g., 101 for line 1).
b.For Line Group Access:
i.Dial the Line Group code (9 or...

Tie Lines
DSX Software ManualFeatures◆347
Features
Intercom
To place an Intercom call: 1.
Access the tie line.
2.Dial the extension number. • To call the remote system’s operator, dial 
0.
• The call rings the destination extension.
Night Service / Night Ring
To answer a call ringing over the paging system: 1.
Access the tie line.
2.Dial *0.
Speed Dial (System)
To dial a Speed Dial number in the remote system: 1.
Access the tie line.
2.Dial # and the System Speed Dial bin number (e.g., 201-299).
3.The...

Tie Lines
348◆Features DSX Software Manual
Transfer
To transfer your call to a user in the remote system: 1.
Place or answer call. • Transferring an outside call over the tie line requires that the tie line have Tandem Calls enabled and that the extension have Unsupervised Conference enabled in their Class of Service.
2.Press TRANSFER, access the tie line, and dial the extension to which you want to Transfer the call.
• To Transfer the call to the remote voice mail Automated Attendant, dial the voice...

Time and Date
DSX Software ManualFeatures◆349
Features
Time and Date
Description
The system Time and Date appears on display telephones and Station Message Detail Re\
cording reports. 
The system administrator can change the time and date from the system pr\
ogramming mode. In addition, 
extension users can change the time and date from the User Programmable F\
eatures. Although the data is 
entered in 24-hour format, it always displays in 12-hour format (e.g., 1300 = 1:00PM). The system can auto-...

Time and Date
350◆Features DSX Software Manual
Other Related Features
Features
Battery Backup  (page 38)
The battery on the CPU PCB backs up the CPU Real Time Clock for 10-14 days.
Station Message Detail Recording  (page 328)
Time and date appear on the SMDR report.
IntraMail Features None
Operation
User Programmable Feature
Changing the System Time and Date
Feature Mnemonic Operation Access Level
Time and Date#TD (#83) #TD + Enter time in 24-hour clock using hours (2 digits), 
minutes (2 digits) and...