NEC Dsx 34b Manual

Station Message Detail Recording
DSX Software ManualFeatures◆331
Features
Programming
1.If yes:
- In  1541-01: SMDR Port  (page 666), enter 
1 to enable the RS-232 port to output SMDR.
- In  1101-01: Baud Rate  (page 603), set the baud rate of the RS-232 port:
1 for 2400
2 for 9600
3 for19,200
4 for 38,400
5 for 57,600
2.If no:
In  1541-01: SMDR Port  (page 666), enter 
0.
1.If yes, in 1541-02: Print SMDR Headers  (page 666) enter Ye s.
2.If no, in 1541-02: Print SMDR Headers  (page 666) enter No.
1.To...

Station Message Detail Recording
332◆Features DSX Software Manual
Operation
SMDR is automatic once enabled. 

System Administrator (PC Program)
DSX Software ManualFeatures◆333
Features
System Administrator (PC Program)
Description
Available. See  PC Program (System Administrator)  (page 272) for more. 

System Identification
334◆Features DSX Software Manual
System Identification
Description
The system administrator can enter the site name and telephone number in\
to the system data base. This 
information is saved into system memory.
Conditions
• None
Default Setting
• No entries.
Programming
1.In 1011-01: System Name  (page 597), enter the site name.
2.In 1011-02: Telephone Number  (page 597), enter the site telephone number.
Other Related Features
N/A
Operation
N/A.
Store the site name and telephone...

System Programming Backup and Restore
DSX Software ManualFeatures◆335
Features
System Programming Backup and Restore
Description
To prevent the loss of essential custom site programming, use a CompactFlash Ca\
rd plugged into the Intra-
Mail CompactFlash slot to back up the system database. If the need arise\
s, you can restore the system data-
base saved on the card. You can store the system database on the IntraMail CompactFlash Card or o\
n a 
separate FAT16 or FAT32 formatted CompactFlash card. The...

System Programming Password Protection
336◆Features DSX Software Manual
System Programming Password Protection
Description
The system controls access to the programmable options according to the \
programming password the 
administrator enters. There are three password levels:
Conditions
• When programming passwords, the system will enforce the  higher level password if there are dupli-
cate entries. For example, if you inadvertently set the level 3 (Installer) password the same as either 
level 1...

System Programming Password Protection
DSX Software ManualFeatures◆337
Features
IntraMail Features
None
Operation
None 

T1 Lines
338◆Features DSX Software Manual
T1 Lines
Description
T1 lines require a unique T1 PCB (P/N 80061) and give the system a maximum of 24 lines in a single PCB 
slot. The available T1 line types include:
❥Loop Start (DTMF and Dial Pulse)
❥Ground Start (DTMF and Dial Pulse)
❥Direct Inward Dial (DID) Wink Start (DTMF and Dial Pulse)
❥Direct Inward Dial (DID) Immediate Start (DTMF and Dial Pulse)
❥E&M Tie Line Wink Start (DTMF and Dial Pulse)
❥E&M Tie Line Immediate Start (DTMF and Dial Pulse)
T1...

T1 Lines
DSX Software ManualFeatures◆339
Features
Programming
1.Be sure your T1PCB is installed and connected, and that your telco is providing T1 service.
2.In 3101-01: Line Type  (page 809), enter the correct circuit type for each T1 line.
•
00 for uninstalled
•
01 for Loop start
•
02 for Ground Start
•
03 for DID Wink Start
•
04 for DID Immediate Start
•
05 for E&M Wink Start
•
06 for E&M Immediate Start
3.In  3101-03: DTMF Dialing  (page 811), indicate whether the line is DTMF (1) or Dial Pulse...

T1 Lines
340◆Features DSX Software Manual
1.To enable ANI-based Caller ID, in 3121-01: Caller ID Type (page 825) enter 3.
2.In 3121-02: ANI/DNIS Format  (page 825), specify the type of ANI/DNIS received from the telco:
-
0 for no ANI/DNIS data
-
1 for ANI
-
2 for *ANI*
-
3 for *DNIS*
-
4 for *ANI*DNIS*
3.In  3121-03: ANI/DNIS Delimiter  (page 826), select the type of ANI/DNIS delimiter required by your 
connected service - This is required  only for options 2-4 in step 2.
- The delimiter can be any...