NEC Ds2000 Software Instructions Manual

1000 - Trunk Programming
1001 - Trunk Port Description
DS1000/2000 Software Manual Chapter 2: Programming503
Telephone Programming Instructions
1. Enter the programming mode.
2. 1001 + 
HOLD
3. Enter the number of the trunk you want to program (1-48 in DS2000, 1-6 in DS1000) + 
HOLD.
Trunk Toll  Restriction 
LevelUse this option to set the Toll Level of the 
trunk during the day mode. If this Toll Level 
is higher than the extension’s Toll Level, it 
may cause additional dialing restrictions. If 
it is...

1000 - Trunk Programming
1001 - Trunk Port Description
504Chapter 2: ProgrammingDS1000/2000 Software Manual
 The previously programmed value displays.
4. Enter the new trunk circuit type + 
VO L .
OR
Press 
VO L  to leave the current circuit type unchanged.
The extension number programmed in 0504 - Trunk Port Extension Numbers (Fixed 
Slot) on page 476displays. You cannot edit this option.
5. Press 
VO L .
Enter the trunk name. Refer to Programming Names and Text Messages on page 439 if 
you need...

1000 - Trunk Programming
1001 - Trunk Port Description
DS1000/2000 Software Manual Chapter 2: Programming505
Press VO L  to leave the current assignment unchanged
12. Enter the new Toll Level for the trunk (1-7) + 
HOLD.
OR
Press 
VO L  to leave the current Toll Level unchanged
Press 
VO L  to leave the current assignment unchanged.
13. Enter Y  + 
VO L  to override (release) Toll Restriction for the trunk.
OR
Enter N + 
VO L  to enforce the extension’s Toll Restriction.
OR
Press 
VO L  to leave...

1000 - Trunk Programming
1002 - Trunk Groups
506Chapter 2: ProgrammingDS1000/2000 Software Manual
1002 - Trunk Groups
Description
Use Program 1002 - Trunk Groups to assign trunks (1-48 in DS2000, 1-6 in DS1000) to trunk 
groups (0-8). This program also lets you assign the priority of trunks within each group. When a 
user seizes a trunk group, the system selects the lowest order trunk in the group first. If the lowest 
order trunk is busy or out of service, the system searches sequentially by order...

1000 - Trunk Programming
1002 - Trunk Groups
DS1000/2000 Software Manual Chapter 2: Programming507
In DS2000, trunks must be on installed PCBs.
You can only enter a trunk into a Trunk Group it the PCB for that trunk has been properly 
installed in 9902 - Slot Assignment. 
In addition, if you program a trunk into a group and later on use 9902 - Slot Assignment to 
remove that trunk’s PCB, the system automatically removes the trunk from the group.
Conditions
None
Table 37:  Program 1002 - Trunk Groups...

1000 - Trunk Programming
1002 - Trunk Groups
508Chapter 2: ProgrammingDS1000/2000 Software Manual
Telephone Programming Instructions
1. Enter the programming mode.
2. 1002 + 
HOLD
3. Select the trunk group you want to program + HOLD.
 The trunk currently assigned to order 01 displays.
4. Enter the trunk you want to assign to order 01 + 
VO L .
OR
Press 
VO L  to leave the current assignment unchanged and advance to the next entry.
5. When you are done entering data for the group, press 
HOLD
6. Return...

1000 - Trunk Programming
1003 - Trunk Options
DS1000/2000 Software Manual Chapter 2: Programming509
1003 - Trunk Options
Description
Use Program 1003 - Trunk Options to program various options for trunks.
Note: If you are doing extensive programming, you may find Program 9801 - Copy Command 
(page 557) saves you time when customizing this option.
Also see Program 1001 - Trunk Port Description on page 498.
Conditions
NoneDS2000 Fixed Slot
Available.
DS2000 U Slot
DS1000 Available. Trunks 4-6 require the...

1000 - Trunk Programming
1003 - Trunk Options
510Chapter 2: ProgrammingDS1000/2000 Software Manual
Telephone Programming Instructions
1. Enter the programming mode.
Direct Termination 
(Night)If the trunk is a Direct Inward Line, use this 
option to set the night termination (answer-
ing point). The DIL rings the answering 
point directly at night. This option has no 
effect on other types of trunks.
• See Direct Inward Line on page 118 for 
more.
• See Key Ring on page 232 for more.NT...

1000 - Trunk Programming
1003 - Trunk Options
DS1000/2000 Software Manual Chapter 2: Programming511
2. 1003 + HOLD
Press CONF at any time to back up to the previous entry. This automatically saves 
your data entry,
3. Select the trunk port you want to program + 
HOLD.
 The previously programmed Pickup Group displays.
4. Enter the number of the Pickup Group to which the trunk should belong (1-8, 0 for unas-
signed) + 
HOLD.
OR
Press 
VO L  to leave the current assignment unchanged and advance to the...

1000 - Trunk Programming
1003 - Trunk Options
512Chapter 2: ProgrammingDS1000/2000 Software Manual
OR
Press 
VO L  to leave the current assignment unchanged and advance to the next entry.
The previously programmed assignment displays.
11. Enter the Distinctive Ringing tone for the trunk (1-8) + 
HOLD.
OR
Press 
VO L  to leave the current assignment unchanged and advance to the next entry.
The previously programmed assignment displays.
12. Enter the MOH source for the trunk (0 = No MOH, 1 = External at...