NEC Ds2000 Software Instructions Manual

0300 - System Options
0302 - System Identification
DS1000/2000 Software Manual Chapter 2: Programming453
Telephone Programming Instructions
1. Enter the programming mode.
2. 0302 + 
HOLD
3. Enter the system name (up to 14 characters) + VO L .
(Refer to Programming Names and Text Messages on page 439 if you need help in entering 
names)
OR
Press 
VO L  to scroll to the next option.
After pressing 
VO L  to scroll to the next entry, you can press CONF to exit the pro-
gram.
4. Enter the site phone...

0300 - System Options
0302 - System Identification
454Chapter 2: ProgrammingDS1000/2000 Software Manual
OR
Press 
CONF to exit the program. 

0400 - Timers
0401 - System Timers
DS1000/2000 Software Manual Chapter 2: Programming455
0400 - Timers
0401 - System Timers
Description
Use Program 0401- System Timers to enter the values for system-wide timers. Conditions
NoneDS2000 Fixed Slot
Available. DS2000 U Slot
DS1000
Table 24:  Program 0401 - System Timers
OptionDescriptionEntriesDefault
Park Orbit
Use this timer to set how long a call stays in 
System Park Orbit before it recalls the exten-
sion that parked it. This timer if for orbits 
60-67...

0400 - Timers
0401 - System Timers
456Chapter 2: ProgrammingDS1000/2000 Software Manual
Intercom Inter-digitWhen an extension user places a call, they 
must dial each succeeding digit within this 
interval.
The system also uses this interval for an 
extension going into the talk state, which 
affects the Modem Cut-Though timing. Set-
ting this timer too short or too long could 
effect DTMF receiver usage and create block-
ing. Normally, you should leave this timer at 
its default value (6 seconds). Some...

0400 - Timers
0401 - System Timers
DS1000/2000 Software Manual Chapter 2: Programming457
Trunk RevertThis timer sets how long Hold Recall rings 
the extension that placed the call on hold 
before Key Ring occurs. Key Ring rings all 
extensions programmed to ring for that line.
• See Hold on page 197 for more.
• See Key Ring on page 232 for more.
This timer also sets how long a DIL to a 
Ring Group master number rings an idle 
extension before Key Ring or overflow 
occurs. Key Ring rings all extensions...

0400 - Timers
0401 - System Timers
458Chapter 2: ProgrammingDS1000/2000 Software Manual
Telephone Programming Instructions
1. Enter the programming mode.
2. 0401 + 
HOLD
3. Enter data for the displayed timer + HOLD.
OR
Press 
VO L  or VO L  to scroll to the timer you want to change + HOLD
4. Enter data for the displayed timer + HOLD
5. Press VO L  or VO L  to scroll to another timer.
OR
Press 
HOLD to return to step 2 and enter another program number.
Program Lockout TimeOnce the system locks out a...

0400 - Timers
0402  - Trunk Timers
DS1000/2000 Software Manual Chapter 2: Programming459
0402  - Trunk Timers
Description
Use Program 0402- Trunk Timers to enter the values for trunk timers.
Conditions
NoneDS2000 Fixed Slot
Available. DS2000 U Slot
DS1000
Table 25:  Program 0402 - Trunk Timers
OptionDescriptionEntriesDefault
Camp-On
• Not used.CAMP ON?0-9999 sec.60 sec.
Line ResponseWhen the system fails to detect loop current 
on a trunk, it will wait this interval before 
marking the trunk as...

0400 - Timers
0402  - Trunk Timers
460Chapter 2: ProgrammingDS1000/2000 Software Manual
PBX/Centrex FlashUse this timer to set the Flash interval. When 
a user flashes a trunk (manually or in a 
Speed Dial number), the system opens the 
trunk circuit for this interval. For accurate 
flash function, be sure to set this interval for 
compatibility with the connected telco or 
PBX/Centrex.
If you set this interval too short, the telco 
may not always register the flash. If too long, 
inadvertent disconnects...

0400 - Timers
0402  - Trunk Timers
DS1000/2000 Software Manual Chapter 2: Programming461
Minimum Ring Detection 
TimerUse this timer to set the threshold for ring 
detection. If the ring signal is longer than 
this interval, the system interprets the signal 
as valid ringing. If the signal is equal to or 
shorter than this interval, the system ignores 
the ringing.
Be sure the value you enter is compatible 
with the local telco. If you set this value too 
short, the system may detect line spikes and...

0400 - Timers
0402  - Trunk Timers
462Chapter 2: ProgrammingDS1000/2000 Software Manual
Manual DTMF Tone OnThis timer sets the duration of DTMF digits 
for trunk calls manually dialed by an exten-
sion user. This is required because the sys-
tem buffers the digits the user dials.
Set this timer for compatibility with the con-
nected telco or PBX/Centrex. If you set this 
interval too short, the telco or PBX/Centrex 
may not be able to properly detect the 
DTMF digit. If too long, outbound dialing is...