NEC Ds2000 Software Instructions Manual

1800 - Extension Options
1807 - Extension Options (Part 2)
DS1000/2000 Software Manual Chapter 2: Programming553
1807 - Extension Options (Part 2)
Description
Use Program 1807 - Extension Features (Part 2) to additional options for extensions. Also see 
Program 1801 - Extension Port Description on page 532 and Program 1802 - Extension Options 
(Part 1) on page 539.
Note: If you are doing extensive programming, you may find Program 9801 - Copy Command 
(page 557) saves you time when customizing this...

1800 - Extension Options
1807 - Extension Options (Part 2)
554Chapter 2: ProgrammingDS1000/2000 Software Manual
Telephone Programming Instructions
1. Enter the programming mode.
2. 1807 + 
HOLD
3. Enter the number of the extension you want to program (300-395) + HOLD
OR
Press 
HOLD to select extension 300.
Hunt TypeUse this option to assign the hunt type for 
the extension. The options are:
1 = Ring No Answer Trunk (TRUNK RNA)
2 = Busy/Ring No Answer Trunk (T BUSY 
RNA)
3 = Busy/Ring No Answer All Calls...

1800 - Extension Options
1807 - Extension Options (Part 2)
DS1000/2000 Software Manual Chapter 2: Programming555
 The previously programmed value displays. The top line of the display indicates the 
extension port you are programming.
4. Enter Y to enable or N to disable incoming voice-announced Intercom calls while the exten-
sion is in the headset mode + 
VO L 
OR
Press 
VO L  to leave the current entry unchanged.
The previously programmed value displays.
5. Enter Y to enable or N to disable Paging...

1800 - Extension Options
1807 - Extension Options (Part 2)
556Chapter 2: ProgrammingDS1000/2000 Software Manual
11. Enter Y to enable or N to disable the headset mode for the extension + VO L 
OR
Press 
CONF to select another extension port.
OR
Press 
CONF twice times to exit the program. 

9800 - System Utilities, Part 1
9801 - Copy Command
DS1000/2000 Software Manual Chapter 2: Programming557
9800 - System Utilities, Part 1
9801 - Copy Command
Description
Use Program 9801 - Copy Command to copy Class of Service, extension and trunk data. You can 
copy data from a single source to a single destination, or from a single source to a range of COSs, 
extensions or trunks. 
Program 9801 - Copy Command will copy data in the following programs:
Program 0101: Class of Service Options
Program...

9800 - System Utilities, Part 1
9801 - Copy Command
558Chapter 2: ProgrammingDS1000/2000 Software Manual
7. If copying to a single destination, enter the same destination trunk or extension you entered in 
step 5 above.
OR
If copying to a range of extensions or trunks, enter the highest numbered extension or trunk in 
the range.
8. Press 
HOLD.
9. Press
 CONF to select another program to copy.
OR
Press 
CONF twice to exit the program.
COPY (program)    (source)
COPY COMPLETE! 

9800 - System Utilities, Part 1
9802 - Swap Command Utility (U Slot)
DS1000/2000 Software Manual Chapter 2: Programming559
9802 - Swap Command Utility (U Slot)
Description
Use 9802: Swap Command to swap extensions, trunks, or slot positions. Use this option as an 
alternative to manual cross-connect or extensive reprogramming.
Keep the following in mind when using 9802: Swap Command:
The system will prevent you from swapping an extension with a trunk.
When you swap extensions, all the programmed...

9800 - System Utilities, Part 1
9802 - Swap Command Utility (U Slot)
560Chapter 2: ProgrammingDS1000/2000 Software Manual
2. 9802 + HOLD.
3. Enter 
E. You  see:
4. Enter the number of the first PCB/slot you want to swap + 
HOLD.
5. Enter the number of the second PCB/slot you want to swap + 
HOLD.
6. Following the instructions in your Hardware Manual, unplug the swapped PCBs/slots and 
plug them into their new locations.
7. Press 
HOLD to retrun to step 2 to make another swap.
OR
Press 
HOLD + CONF to...

9900 - System Utilities, Part 2
9901 - Reset Station Port
DS1000/2000 Software Manual Chapter 2: Programming561
9900 - System Utilities, Part 2
9901 - Reset Station Port
Description
Use Program 9901 - Reset Station Port to reset an extension.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9901 + 
HOLD
3. Enter the number of the extension you want to program (300-395) + HOLD.
 The first line of the display indicates the station port you have selected.
4. Press 
HOLD...

9900 - System Utilities, Part 2
9902 - Slot Assignment
562Chapter 2: ProgrammingDS1000/2000 Software Manual
9902 - Slot Assignment
Description
Use Program 9902 - Slot Assignment to assign PCBs to slots. Only use this program if the default 
U Slot configurations do not meet the site requirements. When you first install your system, the 
default slot assignments follow the charts below.
Conditions
NoneDS2000 Fixed Slot Not available.
DS2000 U Slot Available.
DS1000 Not applicable.
4 and 8 Slot Systems with...