NEC Ds2000 Software Instructions Manual

9900 - System Utilities, Part 2
9902 - Slot Assignment
DS1000/2000 Software Manual Chapter 2: Programming563
Telephone Programming Instructions
Using Program 9902: Slot Assignment
Step 1: Review the Default Configuration
1.1  Check the default configuration to see if it meets the site requirements. If it does, you 
won’t have to make any of the changes in the following steps.
Step 2:
 Map Out Your Installation
2.1  If you need to reconfigure your PCBs, use the table below to determine in which slots you...

9900 - System Utilities, Part 2
9902 - Slot Assignment
564Chapter 2: ProgrammingDS1000/2000 Software Manual
5.9  VOL  or VOL  to select another slot, or press CONF to exit program 9902.
Step 6:
 Programming (Adding) an Empty Slot
During programming, you may see the following error messages:
6.1  Enter the programming mode and dial 9902 + HOLD to enter program 9902: Slot Con-
trol.
6.2  Press HOLD then VOL  or VOL  until you select the empty slot you want to program 
(2-8).
6.3  Press HOLD. You  see...

9900 - System Utilities, Part 2
9902 - Slot Assignment
DS1000/2000 Software Manual Chapter 2: Programming565
Step 7: Verify Your Slot Entries
Use the following steps to check your 9902: Slot Control programmed entries.
7.1  Enter the programming mode and dial 9902 + HOLD to enter program 9902: Slot Con-
trol.
7.2  Press HOLD then VOL Up or VOL Down until you select the slot you want to check (1-
8).
7.4  Once you’ve selected the slot you want to check, press V. The display shows the number 
of circuits...

9900 - System Utilities, Part 2
9905 - Password
566Chapter 2: ProgrammingDS1000/2000 Software Manual
9905 - Password
Description
Use Program 9905 - Password to change the system passwords. The table below shows the default 
system passwords. Turn to System Programming List on page 360 for more on the system pass-
words.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9905 + 
HOLD
3. Enter the level (1-3) for the password you want to change + HOLD. 
4. Enter the new...

9900 - System Utilities, Part 2
9906 - Database Save
DS1000/2000 Software Manual Chapter 2: Programming567
9906 - Database Save
Description
Use Program 9906 - Database Save to back up site data to PC Card P/N 85880 or P/N 80050-
V**.**. Refer to your Hardware Manual for the specifics.
Conditions
The following table lists the PC Card Backup Error Messages that you may see when using the 
instructions below.
Telephone Programming Instructions
1. Insert the PC Card into the CPU.
Refer to the Hardware Manual...

9900 - System Utilities, Part 2
9906 - Database Save
568Chapter 2: ProgrammingDS1000/2000 Software Manual
You see the address, name and date of the first data base stored. If you data bases are 
stored, you see:
8. The system assigns the name you entered in step 7 to the address you select below:
- Press VOL 
 or VOL  to scroll through the 12 data base addresses (DB 00 through DB 11)
OR
- Skip this step to select the currently displayed data base.
9. Press 
HOLD.
Normally, you see:
The PC Card Active...

9900 - System Utilities, Part 2
9907 - Database Load
DS1000/2000 Software Manual Chapter 2: Programming569
9907 - Database Load
Description
Use Program 9907 - Database Load to load site data previously saved to PC Card P/N 85880 or P/
N 80050-V**.** into the system data base. Refer to your Hardware Manual for the specifics.
Conditions
The following table lists the PC Card Load Error Messages that you may see when using the 
instructions below.
Telephone Programming Instructions
1. Insert the PC Card into...

9900 - System Utilities, Part 2
9908 - PC Card Erase Utility
570Chapter 2: ProgrammingDS1000/2000 Software Manual
9908 - PC Card Erase Utility
Description
Use Program 9908 - PC Card Erase Utility to completely erase all the data bases in a Data Base 
PC Card (P/N 85880).
Conditions
None
Telephone Programming Instructions
1. Following the instructions in your Hardware Manual, insert Data Base PC Card (P/N 85880) 
into the CPU.
2. Be sure the CPU mode switch is set to 
RUN.
3. Enter the programming mode....

9900 - System Utilities, Part 2
9999 - System Initialization
DS1000/2000 Software Manual Chapter 2: Programming571
9999 - System Initialization
Description
Use Program 9999 - System Initialization to initialize the system database.
Conditions
None
Telephone Programming Instructions
1. Enter the programming mode.
2. 9999 + 
HOLD
3. Enter Y  + HOLD to initialize the system.
OR
Enter N + 
HOLD to exit the program without initializing.
If you enter Y, the system will initialize with the factory-installed...

9900 - System Utilities, Part 2
9999 - System Initialization
572Chapter 2: ProgrammingDS1000/2000 Software Manual