Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

SECTION MITL9141-753-503-NAConnector Pin Assignment Tables
2.05The RS-232 connectors used on the 
DATASET 1100 series have
the following pin assignments when operating in Data Commu-
nications Equipment (DCE) mode:
Signal
Designation
PinDirection
TXD
RXD
RTSCTS
DSRDCD
DTR
RIframe ground
1transmit data
2receive data
3ready to send4
clear to send
5data set ready
6signal ground
7data carrier detect
8data terminal ready20
ring indicator22
reserved input25to 
DATASETfrom 
DATASETto 
DATASETfrom 
DATASETfrom...

DATASET 1100 Series
3. 
DATASET 1101
Description
3.01A DATASET 1101 is mounted within a SUPERSET 3TMDN or a
SUPERSET 4TMDN telephone. It is 13 x 13 cm (5 x 5 inch) and
connects via an internal cable to the telephone set circuit board; it
interfaces to the PABX Digital Line Card through the same pair of wires
that the telephone set voice circuit uses. Although the 
DATASET 1101
Cartridge has 
LEDs near its connectors, its primary interface to the
user is through two programmable line appearance keys and...

SECTION MITL9141-753-503-NAIt also has an internal ribbon cable connecting it to the telephone set;
its connection to the PABX is through the set’s twisted pair.
Installation
3.06The 
DATASET 1101 Cartridge is internal to the telephone set;
only two connections (power and RS-232) are required, in addi-
tion to the set’s connection to the PABX.
3.07 Complete Customer Data Entry for the system to allow the
DATASET 1101 Cartridge to operate with the PABX.
3.08Connect an RS-232 cable between the RS-232...

DATASET 1100 Series
NOTE-
GATASET 1101 CARTRIDGE IS AN
INTEGRAL INTERNAL PART OF THE TELEPHONE
SET. IT IS NOT FIELD ACCESSIBLE.
liDATA
LCDATTN
KEY
/
TVPICAL LINE APPEARANCE
KEY ASSIGNMENT ON A
SUPERSET 4-‘DN TELEPHONE
DISC‘KEY
RiD
TxDIIRS-232POWER
CONNECTOR
KAO486R3E5Figure 3-l 
DATASET 1101 Cartridge, Showing Connectors and indicators
Page 7 

SECTION MITL9141-753-503-NARS-232C OR v.24
1PHYSICAL PORT
SINGLETWISTED PAIR
DNIC LINE CARD
12 PORTS/CARD
TELEPHONES WITH 
DATASET 1101 CARTRIDGE
cJ
TERMINAL OR PC
KA0402ROE3Figure 3-2 Typical 
DATASET 1101 Cartridge Application
Page 8 

DATASET 1100 Series
4. 
DATASET 1102 DUAL RACK MOUNTED CARD
Description
4.01A DATASET 1102 Dual Rack Mounted card contains two DATA-
SETS mounted on a common pcb; it has LEDs on its front panel,
but no switches or keys for manual operation. Each 
DATASET 1102
Dual Rack Mounted card, which is installed within a data cabinet,
interfaces to a a PABX Digital Line Card circuit through a single pair.
The DATASHELF 9100 connects to the PABX through a 25-pair cable;
each card slot is assigned one of these pairs....

SECTION MITL9141-753-503-NA4.04The 
pinout of the card edge connector is as follows:
PinSignal
1data ring
2no connection
3frame ground
4signal ground
5Tl (ac input)
6T2 (ac input)
7T2 (ac input)
8Tl (ac input)
9signal ground
IOframe ground
11no connection
12data tip
installation
4.05Complete system cabling and Customer Data Entry for the slot
into which the 
DATASET is being installed; cabling is defined in
DATASHELF 9100 installation procedures.
4.06Install a 
DATASET 1102 Dual Rack Mounted card by...

DATASET 1100 Series
KA0332RlFigure 4-1 
DATASET 1102 Dual Rack Mounted card
Page 11 

SECTION MITL9141-753-503-NA
- Page 12 

DATASET 1100 Series
5. STANDALONE 
DATASET 1103
Description
5.01A Standalone DATASET 1103 is packaged in a flat case which
can be placed under a standard desk telephone set. It is func-
tionally the same as the 
DATASET 1101 Cartridge or one-half of the
DATASET 1102 Dual Rack Mounted card (it shares the same base pcb
as the 
DATASET 1102 Dual Rack Mounted card). The Standalone
DATASET 1103 can be connected to the PABX using a four-wire con-
nection; two wires connect the 
DATASET to the Digital Line...