Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

SECTION MITL9141-753-525-NAPage 8 

Datacabinet 9000
4. DATACABINET 9000 INSTALLATION AND WIRING
General4.01Unpack the DATACABINET 9000 and check it for dama,ge or
missing items. Position the cabinet where it is to be installed
and equipped. install the shelves and cables within the cabinet accord-
ing to Chart 4-1.
Notes:1. Each card slot not equipped with a 
DATASET set must be
equipped with a filler plate to maintain correct flow of
cooling air within the shelves; this does not apply to the
top shelf of any configuration.
2. Only 
MITEL...

SECTION MITL9141-753-525-NACHART 4-l (CONT’D)
INSTALL SHELVES, CABLES, AND OTHER ASSEMBLIES INTO A 
DATACABINET 9000
StepAction
10Form each cable bundle neatly up the right side rail, as shown in Figure 2-2, and
attach securely to the brackets on the side rails.
11Install 25-pair cables in through one of the three cable entry slots on the rear PDU
panel and route up the left side of the cabinet to the associated shelves; attach to
side rail brackets separately from ac cords.
12
13
14Close up the covers...

Datacabinet 9000CARDFILE RAIL
I
FAN UNIT
KAO601 ROE0Figure 4-l Installation of 
Cardfile Rail
Page 11 

SECTION MITL9141-753-525-NAATASHELF 
9100 i
)ATACABINET 9001;lDE RAIL
GROUNDWIRE
CARDFILIRAILi
7
!J
-
a
a
a-
00
0
0
]-
i-
-
Ii
T
0
I
8
0
0--+
0
00
0
0
0
00
0
0Figure 4-2 Connection of Shelf Ground Wire
Page 
12 

MITEL STANDARD PRACTICESECTION MITL9141-753-526-NAIssue 3, April 1988
DATASHELF 9 100
@Copyright 1988, MITEL Corporation. All rights reserved.
T”Trademark of MITEL Corporation
@Registered Trademark of MITEL Corporation 

SECTION MITL9141-753-526-NAWARNING
THIS EQUIPMENT GENERATES, USES, AND CAN RADIATE RADIO FREQUENCY ENERGY AND, IF
NOT INSTALLED AND USED IN ACCORDANCE WITH THE INSTRUCTIONS MANUAL, MAY CAUSE
INTERFERENCE TO RADIO COMMUNICATIONS. IT HAS BEEN TESTED AND FOUND TO COMPLY
WITH THE LIMITS FOR A CLASS A COMPUTING DEVICE PURSUANT TO SUBPART J OF PART 15
OF FCC RULES, WHICH ARE DESIGNED TO PROVIDE REASONABLE PROTECTION AGAINST
SUCH INTERFERENCE WHEN OPERATED IN A COMMERCIAL ENVIRONMENT. OPERATION OF
THIS...

Datashelf 9100
1. INTRODUCTIONCONTENTSPAGE
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 1
Reason for issue . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . , . . . . . . . 1
2. DATASHELF 9100
General . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3
3. DATASHELF 9100 INSTALLATION AND WIRING . . . . . . , . . . . . . . . . . . . . . 7
FIGURE
2-l
2-2
3-1
3-2
TABLE
2-l
CHART
3-lLIST OF ILLUSTRATIONS...

SECTION MITL9141-753-526-NA
iv 

Datashelf 9100
1. INTRODUCTION
General1.01This Section describes the MITEL DATASHELF 9100, part number
9141-901-IOO-NA. The DATASETs which mount in this shelf are
described in separate practices.
Reason for Issue
1.02 This Section is issued to describe the DATASHELF 9100 in
which 
MITEL rack mounted DATASETs are installed.
Page 1