Mitel SX 200 DIGITAL Pabx Superset 3 Telephone Description Manual

SECTION MITL9109-094-315-NA4-10Audit Printouts. . . , . . . . . . . . . . . . . . . . . . . . . . . . . . 36
vi 

Attendant Console Description
FIGURE
4-11
TABLE
4-1
4-2LIST OF ILLUSTRATIONS (CONT’D)
TITLEPAGECall Restriction Display . . . . . . . . . . . . . . . . . . . . . . . . 38
LIST OF TABLES
TITLE
PAGEAudit Printouts. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34
Automatic Wake-Up Single-Line Report Suffixes . . . . . 40
vi 

Attendant Console Description
1. INTRODUCTION
General1 .OlTwo types of Attendant consoles are available with the
SX-200@ DIGITAL PABX supporting G1003 software. The existing
LCD console, uses four wires and interfaces with the universal card
(console module). The Superconsole 
1000TM attendant console uses
one twisted pair of wires, and interfaces to a Digital line card. The
Superconsole 7000 attendant console has a RS-232 printer port, an
optional tilt display and is designed to work with any of the...

SECTION MITL9109-094-315-NAPage 2 

Attendant Console Description
2. PHYSICAL DESCRIPTION2.01The Attendant Console housing measures 39.4 cm (15.5 inches)
long, 10.2 cm (4.0 inches) high, and 22.9 cm (9.0 inches) deep.
The Attendant Console is shown in Figure 2-l: SX-200 DIGITAL PABX
Attendant Console. The weight of the console is 2.27 kg (5.0 lb) and
consists of two major assemblies: an upper and lower assembly.
Upper Assembly
2.02The upper assembly consists of the following parts:
Keyboard Printed Circuit Assembly: A printed circuit board...

SECTION MITL9109-094-315-NAHand/Headset:The removable hand/headset may be connected to
either jack on the left side of the Attendant Console.
RS-232C Port:A printer or terminal/CRT can be attached to the
Superconsole 1000 attendant console via an RS-232C port, connector.
This allows direct connection to most printers or terminal/CRTs. The
RS-232C interface is programmable from 50 to 2400 baud. Refer to
Appendix A for RS-232C interface specifications.
Page 4 

Attendant Console Description7101R2Figure 2-l SX-200 DIGITAL PABX Attendant Console
Page 5 

SECTION MITL9109-094-315-NA
IANDSETLIQUIDCRVSTALDISPLAV10 DISPLAV ASSOCIATICKEYS (SOFTKEYS)
mF,Do 8F2aC>oF3Wc_) 0F4~c>
flFSD(--) nF7DC> BF8ao mF9D.oOFOD
Volume Volume Contrast conytTelephone Number
Function 
Trunk GYPCancelRelease
0000000
Page
o Blocko Hold 4+ oHold 3’ Hold 2 o Hold 1 oAnswerEl7ao
~‘~0000000 0100
n7 LED14 ATTENDANT CONSOLE
12 DIAL KEVS
INDICATORSKEYS (FIXED KEYS)2 VOLUME CONTROL KEVS
2 CONTRAST CONTROL 
KEVS4 CURSOR CONTROL KEYS
6763R4E~Figure 2-2 Attendant Console Keyboard Layout
Page 6 

Attendant Console Description
3. FUNCTIONAL DESCRIPTION
General3.01The Attendant Console Keyboard layout (refer to Figure 2-2),provides the standard Call Handling keys.
Attendant Function Keys (Fixed Keys)
3.02The following paragraphs describe the operation of the 14 fixed
keys in Call Processing mode.
FUNCTION KEY: This key enables the attendant to access the follow-
ing 
softkey functions:
ATT FUNCTION
DAY NIGHT 1 OR 2
GUEST ROOM FUNCTIONS (if enabled)
FRANCAISAPPLICATION
ALARM (if enabled)
BELL OFF or...

SECTION MITL9109-094-315NA .
ANSWER KEY:When an incoming call is routed to the Attendant
Console the ANSWER LED is flashing and the appropriate 
softkey dis-
play is 
GN. The ANSWER key is used to answer calls in the order in
which they arrived at the Attendant Console. At this time the ANSWER
LED is ON continuously. To answer a specific call the Attendant must
press the appropriate 
softkey.Display Associative Keys (Softkeys)
3.03The 10 Display Associative Keys 
(Fl to FO) are located directly
below the...