Mitel SX-200 DIGITAL Pabx Information Manual

Customer Data Entry (CDE) 
4.41 Commands 
a) The following five softkeys appear only when the TYPE field is set 
to the default value (Speed Dial) and when the cursor is at the TYPE 
field on the command line: 
l-KEY LINE Pressing this softkey sets the selected SUPERSET@ key as 
a Key Line. The form updates and displays Key in the TYPE field. 
P-MULTI-CALL Pressing this softkey designates the selected SUPER- 
SET@ key as a Multiple Call Line. The form updates and displays 
Multiple in the TYPE field....

Customer Data Entry (CDE) 
and then ring the SUPERSET’ set for incoming calls. The Delay indica- 
tion appears in the RING field. 
3-NO RING Pressing this softkey prevents incoming calls from ringing 
the SUPERSET@ set ringer. Only the line appearance flashes. The None 
indication appears in the RING field. 
d) The following two softkey descriptions appear when the TYPE field 
is set to Multiple Call Line and the cursor is at the SECRETARIAL field 
on the command line: 
IsNON SECR Pressing this softkey...

Customer Data Entry (@DE) 
Review List for Form 09 
4.42 This form appears when the REVIEW softkey is pressed for both 
the Station/SUPERSET@ Sets Form and the SUPERSET@ Set 
Lines Form. When entered from the Station/SUPERSET@ Form, this 
form displays a list of all programmed appearances of the selected 
station extension number or SUPERSET@ Prime Line number. When 
entered from the SUPERSET@ Set Lines Form, this form displays ap- 
pearances of the selected key extension number or selected key trunk...

Customer Data Entry (CDE) 
4:26 I-JLJN-86 alarm status = NO ALARM 
LINE : 1101 
l- 
2- BAY 
1 
I 
6-QUIT 7-EXT NUM 
1 
CCT STN/SUPERSEl 
01 SUPERSET 
02 SUPERSET 
03 SUPERSET 
SUPERSET 
J-TRUNK NUMBERj4- KEY 
15- 
s- 
lg- lo- 
ATTENDANT CONSOLE DISPLAY 
LINE : 1101 
Fl> 
FG>QUIT BAY SLOT CCT STN/SUPERSET KEY 
I 1 04 SUPERSET 1 
F2> F3yTRUNK NUMBERF4> F5> 
FI>EXT NUM F8> F9> FO> 
Page 4-48  

Customer Data Entry (CDE) 
Form 10 - Pickup Groups 
4.45 This form specifies the members of each Pickup Group. Refer to 
Table 4-17, Pickup Groups for the form layout. Memberships are 
specified by the extension number of a Rotary Dial or DTMF set or the 
Prime Line number of a SUPERSET’ set. Attendant Consoles are not 
allowed. The SX-200@ DIGITAL PABX with Generic 1001 software sup- 
ports a maximum of 50 Pickup Groups; each group supports a maxi- 
mum of 50 members. 
EXT NUM Field This field lists the...

Customer Data Entry (CDE) 
~. -----m-~-m-TABLE. .4- 17 
[;:. ii. .FORM 10 - PICKUP QROUPS 
CDE TERMINAL DISPLAY 
4 : 26 1 -JlJN-86 alarm status = NO ALARM 
[ PICKUP GROUP : I ] 
l- 2- I 3-INSERT  EXT NUM BAY 
1131 
1132 
1134 
1131 SLT 
1 
1 
1 
1 
l- 4- CCT COMMENTS 
I PURCHASING 
2 PURCHASING 
3 PURCHASING 
I PURCHASING 
I 5-PICKUP GROUP 
6-QUIT 7-EXT NUM 
8-DELETE 9- O- 
ATTENDANT CONSOLE DISPLAY 
[ PICKUP GROUP : 1 ] EXT NUM BAY 
SLT CCT COMMENTS 
1131 2 I 1 PURCHASING 
Fl> F2> FB>INSERT 
F4>...

Customer Data Entry (CDE) 
4.47 Commands 
3-INSERT This softkey adds new members to the Pickup Group. 
Pressing the INSERT softkey clears the command line and moves the 
cursor to the EXT NUM field. The addition is completed by entering a 
valid extension number. The system inserts the addition the line after 
that line that was displayed on the command line. Note that this 
softkey only appears if there is data present in this form. 
5-PICKUP GROUP This softkey selects a Pickup Group. Pressing the...

Customer Data Entry (CDE) 
Form 13 - Trunk Circuit Descriptors 
4.48 Trunk circuit descriptors are similar to Classes of Service. A 
trunk circuit descriptor specifies the hardware options for each 
type of Trunk Card. Refer to Table 4-18, Trunk Circuit Descriptors for 
the form layout. Trunk circuit descriptors are complemented by the 
switch settings on the SX-200@ type Trunk Cards. Refer to the Trunk 
Card Switch Assignments Forms in Part Number 9108-093-206-NA, 
Installation Forms. There are six...

Customer Data Entry (CDE) 
:a TABLE 4-18 
;“‘‘-.- FORM li3 - iRlJNK CIRCUIT DESCRIlhOtiS ” 
L;-- 
CDE TERMINAL DISPLAY 
4:26 I-3UN-86 alarm status = ND ALARM 
DESCRIPTOR TRUNK TYPE NUMBER OF TRKS 
ASSIGNED COMMENTS 
01 
02 
03 
04 
05 
06 
07 
08 
09 
10 
II 
12 4-CIRCUIT CO 
4-CIRCUIT CO 
4-CIRCUIT CO 
B-CIRCUIT CO 
6-CIRCUIT CO 2-CCT DID/TIE 4-CIRCUIT DISA 
01 4-CIRCUIT CO 
‘--lTzzC 
0 
t-6 CCT CO 3-E&M MODULE 4-6 CCT DID‘ 5-** MORE ** 
5-QUIT 7- 
a-SEL. OPTION g-REVIEW O- 
ATTENDANT CONSOLE DISPLAY...

Customer Data Entry (CDE) 
4.50 Commands 
l-4 CCT CO Pressing this softkey assigns the CO Trunk type to the 
selected trunk circuit descriptor. Pressing the ENTER softkey completes 
the selection and the TYPE field displays the 4-CIRCUIT CO prompt. 
2-4 CCT DISA Pressing this softkey selects the DISA Trunk type for 
that trunk circuit descriptor. Pressing the ENTER softkey completes the 
selection and the TYPE field displays the 4-CIRCUIT DISA prompt. 
3-E & M TRUNK Pressing this softkey sets the...