Mitel SX-200 DIGITAL Pabx Information Manual

Customer Data Entry (CDE) 
4.21 Field Description. The header line indicates which set of op- 
tions are selected; either the enabled or disabled options. Note 
that the system timers are included with the enabled options. 
STATUS Field This field specifies which options are enabled, disabled 
or the value of the timers. 
OPTION NUM Field This field lists the option number for each option 
or timer. 
4.22 Commands 
l-DISABLE/ENABLE This softkey has two functions; it disables and 
enables System Options....

Customer Data Entry (CDE) 
5-BOTTOM Pressing the BOTTOM softkey moves the line pointer to 
the last line of the disabled or enabled options. The command line 
displays this line. 
6-QUIT Pressing the QUIT softkey when editing this form returns the 
display to the level before the field was modified. The change is not 
saved. At all other times, pressing this softkey exits Form 04 and 
returns the display to the level where the forms are selected. Refer to 
Table 4-2, Available Forms. 
6-CANCEL Pressing...

Customer Data Entry (CDE) 
Form 05 - Tenant Interconnection Table 
4.23 This form specifies which Tenant Groups may be connected 
together. Refer to Table 4-10, Tenant Interconnection Table. The 
system allows for a maximum of 25 Tenant Groups. Each group speci- 
fies its own trunk answering points, attendant answering points and 
night service status. 
4.24 Field Description. Initially, the system interconnects all Tenant 
Groups. The asterisk (*) character indicates this condition. When 
the system...

Customer Data Entry (CDE) 
TABLE- .4-IO : 
L -~ FOi?i 05 - TENANT INTERCONNECTION TABLE 
CDE TERMINAL DISPLAY 
4:26 I-3UN-86 alarm status = NO ALARM 
01 02 03 04 05 06 07 08 09 IO 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25 
ojo************************ 
02*0*********************** 03**0********************** 
04* * * 0 *‘* * * * * * * * * * * * * * * 1: * * 1: * 
05****0******************** 
06*+***0**+**************** 
07******0****************** 08*******0***+************* 
og********o****************...

Customer Data Entry (CDE) 
4.25 Commands 
4-TOP Pressing the TOP softkey moves the line pointer to the first 
line of the form. The command line displays the first line. 
5-BOTTOM Pressing the BOTTOM softkey moves the line pointer to 
the last line of the form. The command line displays this line. 
6-QUIT Pressing the QUIT softkey when editing this form displays the 
following warning on the command line: DATA HAS BEEN CHANGED 
BUT NOT YET SAVED -- “ENTER” TO SAVE. Pressing this softkey 
again exits Form...

Customer Data Entry (CDE) 
Form 06 - Tenant Night Switching Control 
4.26 In some systems it is necessary for one attendant to control 
the Night Service switching of more than one Tenant Group. 
This form specifies which Tenant Groups are switched to Night Service 
simultaneously. Note that the system defaults to Tenant Groups 
switching to Night Service independently of each other. Refer to Table 
4-l 1, Tenant Night Switching Control. 
TABLE 4-11 
[>, FORM D6 - TENANT NIQHT SWITCHING CONTROL 
., 
CDE...

Customer Data Entry (CDE) 
4.27 Field Description. Initially, the system inhibits Tenant Groups 
from switching each other into Night Service. This condition is 
indicated by the period (.) character. When the system permits Tenant 
Groups to switch each other into Night Service, it is indicated by the 
asterisk (*) character. The Tenant Group numbers are listed in the 
header line and the first column. The letter (0) functions as a marker 
and cannot be modified. 
4.28 Commands 
4-TOP Pressing the TOP...

Customer Data Entry (CDE) 
Form 07 - Console Assignments 
4.29 This form specifies the physical location of each Attendant 
Console. Refer to Table 4-12, Console Assignments for the form 
layout. The default location for an Attendant Console is Bay 2, Slot 3, 
Circuit 1. The location of the Attendant Console must be specified 
because it is interfaced to the system through the Universal Card 
which must be installed in those slots rated for high power consump- 
tion (the upper slots of any digital bay)....

Customer Data Entry (CDE) 
4:26 1 -JUN-86 alarm status = ND ALARM 
TABLE 4-12 
be FORti 07 - CONSOLE ASSIBNMENTS 
CDE TERMINAL DISPLAY 
BAY 
1 
1 
2 
2 
1 
l- SLT CCT EXT NUM cos COR TENANT COMMENTS 
08 
08 
03 
03 02 
04 
02 
04 
02 
I 122 
125 
131 1 
1 
2 i RECEPTION 
2 PURCHASING 
3 MARKETING 
08 
12- 
122 
l-s--- i- 4- 
1 RECEPTION 
B-QUIT 
7-BAY/SLT/CCT a-DELETE 9- 
O- 
ATTENDANT CONSOLE DISPLAY 
5- 
BAY SLT 
CCT EXT NUM cos COR TENANT COMMENTS 
1 08 02 122 I 1 
1 RECEPTION 
Fl7 
F27 F37 F47 F57...

Customer Data Entry (CDE) 
4.32 Commands 
6-QUIT 
Pressing the QUIT softkey when editing this form returns the 
display to the level before the field was modified. The change is not 
saved. At all other times, pressing this softkey exits Form 07 and 
returns the display to the level where the forms are selected. Refer to 
Table 4-2, Available Forms. 
6-CANCEL This softkey appears after the occurrence of a program- 
ming error. Pressing the CANCEL softkey returns the display to the 
level where the...