Mitel SX-200 DIGITAL Pabx Information Manual

Customer Data Entry (CDE) 
6-QUIT Pressing the QUIT softkey when editing this form returns the 
display to the level before the field was modified. The change is not 
saved. At all other times, pressing this softkey exits Form 13 and 
returns the display to the level where the forms are selected. Refer to 
Table 4-2, Available Forms. 
6-CANCEL This softkey appears after a programming error has oc- 
curred. Pressing the CANCEL softkey returns the display to the level 
where the programming error occurred....

Customer Data Entry (CDE) 
Review List for Form 13 
4.51 
This form appears when the REVIEW softkey is pressed in Form 
13 - Trunk Circuit Descriptors. The form lists the trunks that 
use the selected trunk circuit descriptor. Refer to Table 4-19, Review 
List for Form 13 for the form layout. Note that the data in this form 
cannot be modified. 
4.52 Field Description. The header line displays the descriptor 
number and the trunk type. 
TRK NUM Field This field lists the trunk numbers assigned to the...

Customer Data Entry (CDE) 
CDE TERMINAL DISPLAY 
4:26 
I -JtJN-86 alarm status = NO ALARM 
[ 6CCTCOTRUNK: 21 TRK NUM BAY SLT CCT COMMENTS 
l- 
2- 3- 2 
9 
IO 
11 
12 
13 
14 
15 
16 
17 
18 
19 
2 1 
3 
3 
3 
3 
3 
3 
4 
4 
4 
4 
4 
1 
I 5 
5 
5 
5 
5 
6 
6 
5 
5 
5 
5 
6 
5 
14- I 5- * 
+QUIT ‘I-DESC NUMBER 8- S- O-  2 
1 
2 
3 
4 
1 
2 
I 
2 
3 
4 
1 
I 
2 I 
ATTENDANT CONSOLE DISPLAY 
[ 6CCTCOTRUNK: 2 ] TRK NUM 
BAY SLT CCT COMMENTS 
2 1 5 2 
Fl> F2> F3, F4> F5> 
F6=-QUIT 
F7>DESC NUMBER F8> F9> FO>...

Customer Data Entry (CDE) 
4.53 Commands 
6-QUIT Pressing the QUIT softkey returns the display to the point 
where the REVIEW softkey was pressed. 
6-CANCEL This softkey appears after a programming error has oc- 
curred. Pressing the CANCEL softkey returns the display to the level 
where the programming error occurred. The CANCEL softkey appears 
with an error message. Refer to Table 4-45, Programming Error Mes- 
sages for a list of these error messages. 
‘I-DESC NUMBER This softkey selects ‘a t$unk...

Customer Data Entry (CDE) 
Options for Trunk Circuit Descriptors 
4.54 This form appears only when the SEL. OPTIONS softkey is 
pressed (refer to Table 4-18, Trunk Circuit Descriptors). This 
form displays the options (parameters) associated with each trunk type 
assigned to each trunk circuit descriptor. Refer to Table 4-21, Trunk 
Circuit Descriptor Options. 
4.55 Field Description. The header line displays the trunk type, the 
trunk circuit descriptor number and the type of parameter under...

Customer Data Entry (CDE) 
TABLE 4-20 (CONT’D) 
TRUNK HARDWARE OPTIONS 
bunk Type: 6-CIRCUIT CO and B-CIRCUIT DISA (cont’d) 
Supervision Direction: incoming Trunk Calls Also 
Guard Timer (0 - 3000 ms) x (100 ms increments) 
Ring Cycle Timer (6 - 10 s) x (1 s increments) 
Ignore Line Reversal During Seizure 
Ringing Expected 
Ringing Debounce Timer (5 - 12 s) x (1 s increments) 
Seize Timer (10 - 60 s) x (10 s increments) 
Flash Timer (200 - -700 ms) x (100 ms increments) 
Interdigit Timer (300 - 800 ms)...

Customer Data Entry (CDE) 
TABLE 4-20 (CONT’D) 
TRUNK HARDWARE OPTIONS 
Trunk Type: E&M CARD (Cont’d) 
roll Office 
Is this a CO 
DTMF 
Impedance (600 Ohms or Complex) 
Remote End is a Satellite 
Remote End is a Satellite with OPS Lines 
Dictation Trunk .I ._ ..: , ! 
. . 
Twe: P-CCT DID/TIE 
Far-End Gives Answer Supervision 
Inhibit Automatic Supervision 
No Seize Alarm 
No Release Alarm 
Toll Office 
Is this a CO 
DTMF 
Impedance (600 Ohms or Complex) 
Remote End is a Satellite 
Remote End is a...

Customer Data Entry (CDE) 
____~.- -- ~- TABLE 4-21 
,_ FORM 13 - TRUNK CIRCUIT DESCRIPTOR OPTIONS 
CDE TERMINAL DISPLAY 
4:26 1 -JUN-86 alarm status = NO ALARM 
[ 4 CCT CO TRUNK : 2 ] OPTION NAME [SUPERVISION PARAMETER ] 
Far-end gives answer supervision 
Inhibit automatic supervision 
No seize alarm 
No release alarm 
Toll office 
Is this a CO 
DTMF 
Impedance 
Dictation Trunk STATUS 
NO 
NO 
YES 
YES 
NO 
YES 
YES 
COMPLEX 
NO 
Far-end gives supervision NO 
I-YES 2- 3- 4- 5- 
6-QUIT 7- 8- 9- O-...

Customer Data Entry (CDE) 
4.56 Commands 
l-YES, NO, COMPLEX, 600 OHM, 60/40, IMMED This softkey toggles 
the status of the parameters. 
2-30/20, WINK This softkey toggles the status of the parameters. 
3-66/33, DELAY This softkey toggles the status of the parameters. 
4-DELAY INTEG This softkey toggles the status of the parameters. 
B-QUIT Pressing the QUIT softkey when editing this form returns the 
display to the level before the field was modified. The change is not 
saved. The following warning...

Customer Data Entry (CDE) 
Form 14 - Non-Dial-In Trunks 
4.57 This form specifies the characteristics of the system’s Non- 
Dial-In Trunks. These trunks cannot dial any digits into the 
PABX and are usually a CO Trunk. The Day, Nl, N2 answer points are 
assigned in this form. Alternate recall points are assigned in Form 19 
(refer to Table 4-29, Call Rerouting Table). Refer to Table 4-22, Non- 
Dial-In Trunks for the form layout. 
4.58 Field Description 
BAY, SLT, and CCT Fields 
These fields list the...