Mitel SX 200 DIGITAL Pabx General Descriptions Manual

Features Description
lCOS Option 214 (Cannot Dial a Trunk After Flashing) and COS Option 215
(Cannot Dial a Trunk if Holding or Conf with One) prevent trunks from be-
ing accessed as the third party under certain circumstances.
lAn extension with COS Option 233 (Never a Consultee) may not be con-
sulted.
.OSee TRANSFER DIAL TONE for special dial tone on transfer.
0 A call cannot be put on consultation hold if:
- the party is an attendant
- the party is a Call Announce Port,
- the call has an incoming...

Telephone FeatureslIf desired, consult privately with the third party.
SUPERSET 3, SUPERSET 3DN and SUPERSET 4 Telephones
On an Established Call:
lPress the TRANYCONF key -transfer dial tone is returned, the current
party (second party) is on Consultation Hold and hears music, if provided.
lDial the number of the third party.
aIf desired, wait for the third party to answer. (If the number is busy or does
not answer, press the CANCEL key to return to the held call).
lIf desired, consult privately with...

Features Description
Also see BROKER’S CALL (TRADE CALLS) for general information about Bro-
ker’s Calls.
ConcJitionsThe following conditions apply to this feature:
lCOS Option 252 (Transfer With Privacy) is mutually exclusive with the fol-lowing options:
- 302 (Flash-in Conference)
- 224 (Flash for Attendant)
- 223 (Flash Disable)
- 203 (Broker’s Call)
l An extension with COS Option 233 (Never a Consultee) may not be con-
sulted.
lCOS Options 214 (Cannot Dial a Trunk After Flashing) and 215 (Cannot...

5. HOTEL/MOTEL FEATURES
GENERAL5.1 This section describes the hotel/motel features supported by the
SX-200 DIGITAL PABX for Generic 1002 and Generic 1003 software.
5.2 The SX-200 DIGITAL PABX Hotel/Motel feature package integrates stan-
dard PABX features with custom Hotel/Motel features. It is also possible to use
the SX-200 DIGITAL PABX in conjunction with a Property Management Sys-
tem.
Hotel/Motel features available from the Attendant console include:
a check current room status
lmodify room status...

Features Description
Detailed information on the Attendant Console may be found in Practice
9 109-094-3 15-NA, Attendant Console Description.
Attendant Guest Room 
Softkey
Description5.3 This feature gives access to the hotel/motel features available at the atten-
dant console.
The GUEST ROOM 
sof-tkey provides access to the-following features when
pressed :l room number selection
a audit printouts
l room status summary displays
From this level, individual rooms can be selected. After selecting a room,...

Hotel/Motel Features
OperationRefer to Practice 
9109-094-315-NA, Attendant Console Description.Attendant Message Register Audit
Description5.4 This feature allows the attendant to print the message register for all
rooms that have a message register count greater than zero. This feature is
only used in cases where COS Option 703, Message Register Applies, has been
enabled for some extensions; see MESSAGE REGISTER.Conditions
The following conditions apply to this feature:
lConsole cannot request an audit...

Features DescriptionConditionsThe single line printout appears on the Hotel/Motel Wake-up printer.
ProgrammingSee ATTENDANT MESSAGE WAITING SETUP AND CANCEL for basic program-
ming to be able to setup message waiting at an extension.
OperationSee MESSAGING for information on the message waiting feature and ATTEN-
DANT MESSAGE WAITING SETUP AND CANCEL for message waiting changes
from the console.
Enable COS option 105 (Attendant Guest Room Key) for the console to access
message waiting from the Guest Room...

Hotel/Motel FeatureslThe tone used for wake-up calls will be one of 100 ms ON, 400 ms OFF, (re-
peated).
0 System options 12 (Automatic Wake-up Alarm) and 13 (Automatic Wake-
up Print) have no effect on SUPERSET and SUPERSET4DN telephone op-
eration of the feature.
lRecorded announcements are provided through recording hunt groups.
lIf recorded announcement is used, a wake-up will only be honored when
there is a free recording announcement device available. When an exten-
sion answers the wake-up, the...

Features Description
or the wake-up. Refer to Practice 
9109-094-315-NA, Attendant Console De-scription, for a detailed description of the format of the resulting printout.
Assign a printer to the “Hotel/Motel Wake-up” printout type in CDE Form 34
(Directed 
IO) for the status messages for wake-up activity. Audits of wake-
ups from the console are directed to the Hotel/Motel Audit printer; see DI-
RECTED I/O for details on system printers.
Select System Option 
34 (Auto Room StatusConversionIAuto...

Hotel/Motel Features
Call Blocking
Description5.7 This feature allows the attendant to inhibit room to room calls by activat-
ing call blocking from the console. Calls to the attendant or to extensions
without the call blocking COS option selected may be made normally. At-
tempted calls between restricted extensions will be treated as illegal numbers
and the calling party will hear reorder tone. Alternatively Call Rerouting can
be used to intercept blocked calls to an appropriate destination such as the...