Mitel SX 200 DIGITAL Pabx General Descriptions Manual

Data Features
lHeralds and call progress messages are only displayed if programmed; see
DATA TRANSCEIVER (DTRX).
ProgrammingAssign the originating 
dataset a DTE Profile number in CDE Form 12 (Data As-
signment).
Program the Data Circuit Descriptor Options in CDE Form 11 (Data Circuit Des-criptors) 
subform.
Program the DTE Profile in CDE Form 29 (DTE Profile).
OperationDTRX operation is described below.
DTRX Originate
lPress the RETURN or ENTER key on the DTE keyboard. (Keyboard Origina-
tion must be...

Features Description
tors). It must remain off for longer than the duration of the DTR OFF Dis-
connect timer duration.
OR
lPress the BREAK key (if enabled).
OR
lPress the PBX Attention Character key (if programmed).
OR
lPress the ATTENTION key on the dataset.
ORl
Press the DATA CALL ORIGINATE/ATTENTION key on the Digital SUPERSET
telephone.
To disconnect from DTRX and return to idle state:
l At the * prompt, enter BYE or CCTRL E>. “Goodbye” message is dis-
played.
lWhile connected to DTRX, wait for the...

Data FeaturesConditions
None
ProgrammingNone
OperationAt the * prompt, type HELP and the topic name, followed by .
DTRX responds with the required information and returns to the * prompt.
If the topic is not known, just type HELP followed by .
DTRX responds with a list of topics and the ? prompt. Type,the required topic
name, followed by .:To exit from Help, type  at the ? prompt.
DTRX Ho&e
Description6.19 A dataset can be programmed to connect automatically to a predeter-
mined destination when a user...

Features Description
Table 6-1 DTRX Messages(continued)
Message
DO201 Call Failure-BusyMeaning
The destination is busy and queuing is not en-
abled. The user is then returned to the DTRX *prompt. 
_
DO203 Call Failure - Invalid Number, Check Direc-The directory n’umber does not exist. The user istoryreturned to the DTRX * prompt.
DO204 Call Failure -Out of Order, Call Communi-The destination data device has been busied out.
cations DepartmentThis can indicate a fault in the destination data
device.DO205...

Data Features
Table 6-1 DTRX Messages(continued)
Message
503 Facility -Call is QueuedMeanmg
The destination is busy and queuing is enabled.
The “Queue Position” message follows if the des-
tination is a 
dataset. The DTRX is dropped until it
is needed to display the call progress messages, orthe next 
queue:position. When the destination
device becomes free, the “Ringing”and “Con-
nected” messages follow.
57204 Facility- Queue Position nn
.This message occurs after every system clock min-
ute. It...

Features Description
Table 
6-I DTRX Messages
(conti’nued)
MessageMeaning
GO1 10 Information 
- Call Disconnected By Desti-The destination data station disconnected the
nationcall.
GO201 System Error-System Busy, Try Again 
Lat-There are no free DTRX work areas in system
ermemory.
GO301 User Error 
- User Has been inactive for tooDTRX or data call dropped due to inactivity timer
Longexpiry. If in DTRX, “Goodbye” message follows.
GO302 User Error 
- Unrecognized Command,The system could not understand...

Data Features
Modem Pooling is not available with Generic 1002.Conditions
The following conditions apply to this feature:
0COS Option 217 (Direct to ARS) is ignored for outgoing data calls.l
If the originator does not dial a specific Modem Pool Hunt Group access
code, a pooled modem is selected from the default modem pool hunt
group, if programmed.l
On incoming or internal calls, the system prints TRUNK SMDR reports for
the trunk and DATA SMDR reports for the pooled modem if they are en-
abled in the...

Features Description
lBay/Slot/Circuit location of its ONS (or OPS) Line (system-supplied),
lData Circuit Descriptor Number (CDN) that applies to its dataset,
l Bay/Slot/Circuit location of its dataset’s Digital Line,
l extension numberl tenant (default is 
‘l),
l DTE Profile Number (optional),
lClass of Service (COS) (default is 1) and Class of Restriction (COR) (default
is 
l),
0 mode: Answer, Originate, or Both (default is Both).
l 
autodial capability: Auto dial or Non Auto dial (default is Non Auto...

Data Features
Incoming 
DISA Trunk Modem Call
lFrom the Public Network, using a DTMF telephone, dial the DISA tele-
phone number. The PABX answers and returns dial tone.
lDial the DISA Access Code (normal DISA trunk) or Account Code (if a Spe-
cial 
DISA trunk). Once access is allowed, the system returns dial tone.
0 Dial:
- Data Station or Data Hunt Group access code (where default modem
pool hunt group is selected, if programmed)
or,
- Modem Pool Hunt Group access code for DTRX access
- Modem Pool Hunt...

Features Description
- Data Station or Data Hunt Group access code where default modem
pool hunt group is selected, if programmed
- Modem Pool Hunt Group access code for DTRX access
- Modem Pool Hunt Group access code plus Data Station or Data Hunt
Group access code
lWhen answer tone is heard, the modem pooling call is established; put the
modem on line
lIf DTRX access is used, enter CALL followed by the destination data num-
ber or name at the DTRX prompt.
.
Incoming Direct-In-Line (DIL) Modem Calll...