Mitel SX 200 DIGITAL Pabx General Descriptions Manual

Features Description
StatusAbbreviatron
To be InspectedInsp.
Internal
Loca I
Long Distance
Maid in RoomIntLot
LD
Maid
ConditionsThe following conditions apply to this feature:
lIf System Option 2 (Message Lamp Test Enable) is enabled, when a room’s
status is changed from vacant to occupied or from occupied to vacant, the
system performs a message lamp test on the telephone in that room. If the
test finds the lamp defective (i.e. burnt-out or missing), it raises a minor
alarm.
lThe Maid in Room status can...

Hotel/Motel Features
and reserved rooms. Each of these sections is further divided by room condi-tion.
Conditions
Only rooms with CO5 Option 244, Room Status Applies, enabled will be dis-
played by the audit
ProgrammingEnable System Option 27 (Room Status Audit) to allow room status 
pri,ntouts.Assign a printer to the “Hotel/Motel Audit” printout type in CDE Form 34 (Di-
rected IO); see DIRECTED INPUT/OUTPUT for details on system printers.
OperationA complete description of generating a room status...

6. DATA FEATURES
GENERAL
6.1 This part describes the data features supported by the SX-200 DIGITAL
PABX with Generic 1002 and Generic 1003 software. Turn to Appendix C for a
glossary of data terms.
Associated Data Line (ADL)
Description6.2 The Associated Data Line feature provides a telephone with the capability
of originating and disconnecting a data call. The “association” is between a
telephone (used for dialing or disconnecting the call), and a 
dataset to which
the call is switched once the setup is...

Features DescriptionlProgram the associated voice line (AVL) in CDE Form 12 (Data Assignment).
lEnsure that both the originating and destination datasets are both in the
same Operating Mode (asynchronous or synchronous), as programmed in
CDE Form 11 (Data Circuit Descriptors).
ProgrammingAssign Feature Access Code 28 (ADL Call Setup) and Feature Access Code 29
(ADL Disconnect) in CDE Form 02 (Feature Access Codes).
Enable COS Option 900 (Data Station Queuing). When COS 900 is enabled on
a voice...

Data Features
baud rate (this character must be entered within 30 seconds or the call is
released; otherwise reorder tone is heard and PLEASE TRY LATER is dis-
played).l
Connect tone is returned to the originator.l
Hang up the voice telephone.
l Call is switched to the associated dataset.
NOTE: Once the ADL call has been established, the telephone is free to be
used. If a voice call had been established, the other party can be
placed on hold by the 
TRANXONF key, and the ADL call can be es-
tablished....

Features Description
ConditionsRefer to Associated Data Line.
ProgrammingAssign the hotline number in CDE Form 12 (Data Assignment).
OperationTo originate an ADL hotline call:lDial the ADL access code. The call is automatica!ly connected to the preas-
signed destination. Also, a carriage return  may be required de-
pending upon the programmed ADL 
Autobaud option. See ASSOCIATED
DATA LINE 
- flOperation: ADL Gall Originate”.
lIf the destination is busy and queuing is enabled, the originating station is...

Data Featuresl With the handset on-hook, press the PROGRAM 
softkey
lPress the SPEED CALL softkey
l Press an unused SPEED CALL key
lDial the ADL access code
lIf required, dial the Account Code access code and the Account Code
lDial the number of the data destination
lCheck the number to be saved, if correct press the SAVE softkey
SUPERSET 3DN Telephone
At the user’s telephone:
With the handset on-hook, press the PROGRAM feature key
Press an unused SPEED CALL Key
Dial the ADL access code
If required, dial...

Features Description
lGo on-hook when connect tone is heard
lCall is transferred to the associated dataset
To originate a data speed call with voice party on hold:
l Press the programmed Speedcall keyl
If ADL Autobaud is programmed, press CARRIAGE RETURN key
lWhen the connect tone is heard, press the CANCEL key to establish the
data call and transfer the voice call back to the party on hold
SUPERSET 4 Telephone
To originate a data speed call:
l Press the programmed SPEED CALL key
lGo on-hook when connect...

Data Features
To originate a data speed call:
l Press the programmed SPEED CALL key
lGo on-hook when connect tone is heard
lCall is transferred to the associated dataset
To originate a data speed call with voice party on hold:
lPress the programmed SPEED CALL key
lIf ADL Autobaud is programmed, press CARRIAGE RETURN keyl
When the connect tone is heard, press the BACK TO HELD softkey to estab-
lish the data call and transfer the voice call back to the party on hold, or
press NEW CALL to establish the data...

Features Description
ONS voice port and one or more 
SUPfRSET4 or SUPERSET4DN telephones.
The ONS port is connected to Data Terminal Equipment (DTE) via a modem.
Voice only calls, data only calls, simultaneous voice/data calls, and alternating
voice/data calls are permitted.Conditions
The following conditions apply to this feature:
l This feature is available only-on SUPERSET and SUPfRSfT4DN tele-
phones.
lIn a data call; both modems must operate at the same baud rate; one mo-
dem must be in Originate...