Mitel SX 200 DIGITAL Pabx General Descriptions Manual

Features Description
flash permits the user to consult another party and the second switchhook
flash forms a conference.
A variant on Broker’s Call is the Transfer With Privacy feature. This provides
the SWAP functionality without the restrictions on transfers; see Transfer
With Privacy.Conditions
The following conditions apply to this feature:
lWith COS Option 203 (Broker’s Call) enabled in its COS, the industry-stan-
dard telephone cannot set up a conference call or transfer calls.
lThe feature...

Telephone Features
To alternate between calls, flash the switchhook.
SUPERSET Telephones
See SWAP (TRADE CALLS).
CalculatorDescription
4.7 The SUPfRSET4DN telephone provides a basic four function calculator
using the telephone keypad, display, and softkeys.Conditions
This feature is available only on SUPERSET4DN telephones.
ProgrammingNoneOperation
The calculator feature operates as follows:
0 Press SUPERKEY.
l Press CALCULATOR softkey.
The telephone-keypad is used as the numeric keypad; the * key is...

Features Description
lThe SUPERSET telephone must not be Handsfree (using the speaker) at
the time.
lThe Call Announce Port can only handle one caller at a time.
lif the Call Announce Port is busy then the call continues as usual as if the
SUPERSET telephone had been dialed directly.
lThe feature is ignored if the SUPfRSET4 telephone has the Non-busy Ex-
tension feature enabled.
lThe call announce cannot be put on hold or consultation hold or confer-
enced with a party on consultation hold....

Telephone Features
lThe Call Announce Port must be programmed for and connected to the
black/yellow (auxiliary) pair of its associated 
SUPERSET telephone.
lThe Call Announce Port (CAP) must be connected to a COV card, a digital
OPS card or an analog Line Circuit card; hardware restrictions prevent an
ONS port being used for a CAP.
0The Call Announce Port can accept only one caller at a time.
l A Call Announce Port cannot be put on hold or consultation hold or con-
ferenced with a party on consultation...

Features DescriptionOperation
Operation varies depending on the type of telephone as described below.Industry-standard Telephones and 
SUPERSET Telephones
The called extension, hunt group, or Trunk Group is busy. To set a callback:
lDial the Callback - Busy access code within 10 seconds. Dial tone is re-turned.
The extension is now ready for normal use. When the busy party becomes
idle, the set rings:
lLift the handset - ringback or audio for ARS dialing is heard.
lThe required extension rings or the...

Telephone Features
The called extension or Trunk Group is busy, or the called extension does not
answer. To set a callback:
lPress the Call Me Back sof-tkey -dial tone is returned if offhook or the set
goes idle.
The 
SUPERSET4DN telephone is available for normal use.
NOTE: The 
SUPERSET4DN telephone can also dial the Callback access code.
To Answer a Cal I back 
- Busy:
l The SUfJERSET4DN telephone rings. The LCD indicates that a callback is
calling.
lGo offhook - ringback or audio for ARS dialing is...

Features Description
The called extension does not answer. To set a callback:
l Hang up.
l Go off-hook agai.n.
lDial the Callback - No Answer access code.
lDial the unanswered set’s extension number. Dial tone is returned. The set
is available for normal use.
When the called (unanswered) set is used and returned on-hook, the set that
activated the callback gives regular ringing. To answer:
lLift the handset - ringback is heard.
l The required extension rings.
SUPERSET 3DN Telephone
The called extension...

Telephone Features.SUPERSET 4DN Telephone
The called extension does not answer. To set a callback:
lPress the Call Me Back softkey - dial tone is returned. The set is available
for normal use.
NOTE: The 
SUPfRSET4DN telephone can also follow the steps given for in-
dustry-standard telephones, above.
When the called (unanswered) set is used and returned on-hook, the set that
activated the callback gives regular ringing to indicate that a callback is call-
ing.
To answer:
l Go off-hook. 
Ringback is...

Features Description
OperationEstablish a call on a trunk; the LCD displays the duration of the call.Call Park
Description
4.13 This feature allows an industry-standard telephone user to park an ac-
tive call and replace the handset. The call may be retrieved at the extension at
which the call was parked, or from any other extension in the system. If Music
On Hold is available, the parked party hears music. The parking extension may
not originate or receive new calls until the parked call is retrieved;...

Telephone Features
lFlash the switchhook -wait for dial tone.
lDial the Call Park access code-wait for dial tone.
eReplace the handset, or access paging equipment; see PAGING.
To retrieve a parked call from the original extension:l Lift the handset-connection is made.
To retrieve a parked call from another extension:
lDial the Call Park or the Directed Call Pickup access code.
lDial the number of the extension where the call was parked.
lThe call is connected to the remote extension.
Clear All...