Mitel SX 200 DIGITAL Pabx General Descriptions Manual

System FeaturesOperation
Refer to the specific feature in TELEPHONE FEATURES.
SUPERSET3DN TelephoneDescription
Conditions
None
ProgrammingRefer to Practice 
9109-094-2IO-NA, Customer Data Entry (CDE); program
SUPERSET3DN telephones in CDE Form 09 (StationISUPERSETSets); select
their COS Options in CDE Form 03 (COS Define).Operation
Refer to the specific feature in TELEPHONE FEATURES. 3.97 The SX-200 DIGITAL PABX system supports 
SUPERSET3DN electronic tele-
phone sets. The 
SUPERSET3DN telephone has I2...

Features Description
central polling equipment is used for Traffic Measurement, Trunk SMDR,
ACD, DATA SMDR, ACD SMDR, and Analog Networking.Conditions
The System identifier is programmed only from the Attendant Console.
ProgrammingRefer to Practice 
9109-094-315-NA, Attendant Console Description.
OperationNoneTandem Operation
Description3.100 The 5X-200 DIGITAL PABX can support a tandem operation arrange-
ment, using Tie trunks to connect two systems together. See ANALOG NET-
WORKING, SATELLITE PABX, and...

System FeaturesConditions
The following conditions apply to this feature:
lA maximum of 25 Tenant groups may be programmed.
lIf tenanting is used to segregate departments, CDE Form 06 (Tenant Night
Switching Assignment) must be programmed accordingly.
lTenants may have names associated with them; tenant names are not
available in Generic 1002.
ProgrammingAssign consoles to the desired tenant groups via CDE Form 07 (Console As-
signments).Operation
same system. It is also used as a means of selecting...

Features Description
tensions may place. This may mean denying all outside calls, denying calls to
specific locations, denying calls over expensive routes, or any combination of
these.
See AUTOMATIC ROUTE SELECTION (ARS) and CLASS OF RESTRICTION (COR).
ConditionsRefer to Practice 9109-094-22O-NA, Automatic Route Selection and Toll Con-
trol.
Programmingi Refer to Practice 9109-094-220-NA, Automatic Route Selection and Toll Con-
trol.
OperationNone
Tone Plans
Description3.103 To accommodate the numerous...

System Features
l Feature activity
l Guest Room activity
0 Hunt group activity
l Line and Trunk activity
l PCM Channel activity
l Trunk activity
l Trunk group activity
Information is accumulated during a user-programmed time period, and is
then available for output. Programming is done from the Maintenance Ter-
minal or from the Attendant Console.
Refer to Practice 9 
109-094-450-NA, Traffic Measurement.Conditions
None
ProgrammingRefer to Practice 
9109-094-450-NA, Traffic Measurement.
OperationNone...

Features DescriptionTrunk Answer From Any Station (TAFAS)Description3.106 This feature allows the user to answer incoming calls appearing at com-
mon alerting devices (Night Bells). The calls answered can be for a single ten-
ant or for all tenants in the system. The answering extension may then exer-
cise any feature associated with the incoming call that is normally available at
that extension. TAFAS may also be used to answer certain calls which are ring-
ing at the console during the day....

System Features
lWhen the alerting device is heard, go off-hook.
lWhen dial tone is heard, dial the appropriate TAFAS code.
The incoming call is now connected to the answering device.
SUPfRSFT3DN Telephone
To answer a TAFAS call (in the local Tenant group) or any TAFAS call:
lWhen the alerting device is heard, go off-hook.
lPress the NIGHT ANS feature access key.
The incoming call is now connected to the extension.
SUPfRSfT4 and SUPfRSfT4DN Telephones
To answer a TAFAS call (in the local Tenant group) or...

Features Description
Table 3-4 4-Circuit CO & 44rcuit DISA Trunk Hardware Options
Trunk Hardware Option
Reverse to Idle
Far-End Gives Answer Supervision
Inhibit Automatic Supervision
No Seize Alarm
No Release Alarm
Toll Office
Is this a CO
DTMFImpedance (600 Ohms or Complex)
Dictation Trunk
Page 1 of 1
Table 3-5 
64rcuit CO Trunk And 64rcuit DISA Trunk Hardware Options
Trunk Hardware Option
Reverse to idle
IFar-End Gives Answer Supervision
inhibit Automatic Supervision
No Seize Alarm
No Release Alarm...

System FeaturesTable 3-5 6-Circuit CO Trunk And 
6-Circuit DISA Trunk Hardware Options
(continued)
Trunk Hardware Option
Dictation Trunk
Ignore Remote Disconnect
Disconnect Timer (100 to 9900 ms) x (100 ms increments)
Supervision Direction: Incoming Trunk Calls Also
Guard Timer (0 to 3000 ms) x (100 ms increments)
Ring Cycle Timer (6 to 10 s) x (1 s increments)
Ignore Line Reversal During Seizure
Ringing Expected
Ringing 
Debounce Timer (5 to 12 s) x (1 s increments)
Seize Timer (10 to 60 s) x (10 
s...

Features DescriptionTable 3-6 E&M Module and E&M Module 
DISA Trunk Hardware Options
(continued)
Trunk Hardware 
Option
Impedance** Use DIP Switch on the Module to Program **
(600 Ohms or Complex)
E Lead Invert
M Lead Invert** required for type 5 operation **
Disconnect Timer (150 to 300 ms) x (50 ms increments)
Release Acknowledge Timer (2000 to 9900 ms) x (100 ms inc)
Guard Timer (200 to 1000 ms) x (100 ms increments)
Dictation Trunk
Incoming Start Type (Immed, Wink, Delay)
Debounce Timer (20 to 150...