Mitel SX 200 DIGITAL Pabx General Descriptions Manual

System FeaturesTable 3-3 
Digit Translation Plans
Conditions
Only one translation plan may be in effect at a time.
ProgrammingSelect the desired translation plan via System Option 
46 (Digit Translation
Plan o-3 j.
OperationNoneDirect-in Lines 
(DIL)Description
I’3.34 This feature allows non-dial-in type trunks to ring specific answering
points, rather than at the Attendant Console; this may vary with Night Service
changes. An answering point may be one of the following in addition to a
console or LDN:
’...

Features Description
OperationNone
Direct Station Select / Busy Lamp Field (DSS/BLF)
Description3.35 The DSS/BLF feature allows a SUPERSETtelephone to have DWBLF keys
and 
LCDs. The LCDs indicate the status of each associated telephone; pressing
a DSS key immediately transfers a call to the associated telephone.
Conditions 
_The following conditions apply to this feature:
0Line appearance keys on SUPfRSET4, SUPERSETSDN, or SUPERSET4DNtelephones may also be programmed as 
DSS/BLF keys.
0The DSS key is...

System Features
DSS Keys with a 
SUPERSET Telephone
To transfer a call to a station:
lpress the DSS key for that station (Secretarial Option must be enabled). The
call is transferred and the 
SUPERSETtelephone returns to idle or to dialing,
or,
l press the DSS key for that station
lpress RELEASE (for DSS keys without Secretarial Option enabled).
0the call is transferred and the SUPERSETtelephone returns to idle.
Direct to ARS
Description3.36 This option allows an industry-standard telephone to be...

Features DescriptionDirected input/Output
Description3.37 This feature allows the routing of printouts to the system printer port, to
any data port, or to the printer port on the 
SUPERCONSOLE 1000 Attendant
Console. If no new port is specified through CDE, printouts default to the sys-tem printer port. All printer ports are RS-232C interface. Printout types in-
clude:
l Traffic Measurement
l SMDR (Trunk, Data, ACD). CDE
0 Hotel/Motel system printouts
0 PMS interface port
0 ACD Reports
0 Maintenance...

System Features
lThe PMS printer port must be dedicated to PMS only; it cannot be shared
with any other application.
lThe SUPfRCONSOLE 1000 Attendant Console printer port limitations are
described in Practice 9109-094-31%NA, Attendant Console Description.
ProgrammingFor a printer connected via a 
dataset, define an appropriate Data Circuit Des-
criptor in CDE Form 11 (Data Circuit Descriptors). Program the 
dataset in Form
12 (Data Assignment) using the new Data.
Complete programming of Form 34 (Directed...

Features Description
incoming or Attendant calls (discriminating ringing). The system can also be
programmed to provide discriminating ringing for all calls.
Standard ringing1 second on, 3 seconds off
Discriminating ringing
l/2 second on, l/2 second off,
l/2 second on, 2 l/2 seconds off.Conditions
The following conditions apply to this feature:l
Discriminating Ringing does not apply to Night Bells or Recorded An-nouncement Devices. ,
l
The feature applies to both the prime and additional lines on a...

System FeaturesConditionsNone
ProgrammingSpecify the trunk as non-DTMF in CDE Form 13 (Trunk Circuit Descriptors).
OperationNone
Expensive Route WarningDescription3.41 A trunk route can be programmed to give an expensive route warning
tone (three short tones), and on 
SUPERSET telephones, SUPERSET4DN tele-
phones and the console, the LCD displays a message. The user can continue
with the call or hang up and try again later when a less expensive route may
be available. 
SUPERSfT4 and SUPERSET4DN...

Features Description
Flash Control
Description3.42 This set of options limits the use of consultation hold (switchhook flash)
under certain conditions when an extension is in a call with a trunk or at-
tempts to establish a call with a trunk.
Flash On Incoming Trunk
This feature allows extension users to place an incoming trunk on consulta-
tion hold. This enables the trunk call to be transferred, held, or added to a
conference. The option does not apply when the extension is talking to a
DISA trunk that...

System Features
212 (Can Flash if Talking To An incoming Trunk)
213 (Can Flash if Talking To An Outgoing Trunk)
214 (Cannot Dial a Trunk After Flashing)
215 (Cannot Dial a Trunk if Holding or in Conference with a Trunk)
Flash Disable
Description3.43 An extension may be inhibited from using all services requiring the use
of the switch hook flash. For 
SUPERSET telephones, this prevents the exten-
sion from putting a call on consultation hold.Conditions
The following conditions apply to this feature:l
COS...

Features Description
point specified for the given conditions then no call is made and reorder
tone is supplied.
lThis only applies if there is not a call on Consultation Hold.
ProgrammingEnable COS Option 224 (Flash for Attendant) for the extension.
OperationWhile on an established call, flash the switchhook or press the transfer soft-
key. The extension rings the Dial 0 (Attendant) Routing Point; the other party
is placed on consultation hold.
Flash Timing
Description3.45 The flash timer is a...