Lucent Technologies PassageWay Telephony Manager R2.0 For PARTNER Communications System Getting Started Manual

Installing and Configuring Telephony
Manager
2-36
  14.  Choose the Next button.
   The Add to StartUp dialog box appears.
  15.  If you would like to have the Anywhere Dialer application added to
your Startup folder so that it starts every time you start your system,
make sure the first check box is selected. (The check box is selected
by default.) Anywhere Dialer allows you to use Telephony Manager to
dial telephone numbers that are located in other applications.
  16.  If you would like to have...

Installing and Configuring Telephony
Manager
2-37
  20.  When you are finished reading the Readme file, select 
Exit from the
File menu to close the Notepad window.
  
  NOTE:
   If you have any other Notepad windows open, you must close
all of them now. The installation will not continue until all
Notepad windows are closed.
   The About To Restart Windows message box appears.
   Depending on your system, you may have to restart your PC.
  21.  Choose the OK button.
   If the Install dialog box appears,...

Installing and Configuring Telephony
Manager
2-38
Starting Telephony Manager
The first time you start Telephony Manager you are prompted to configure the
following settings:
„the number of call appearances on your telephone. You can enter up to
eight call appearances (six outside lines and two intercom).
„the minimum number or default number of call appearances you want
displayed in the Telephony Manager window. These call appearances
will be displayed even when there is no corresponding call on your...

Installing and Configuring Telephony
Manager
2-39
To start Telephony Manager:
  1.  Select the Start button.
   The Start menu appears.
 2. Select Programs.
  3.  Select the application folder that contains PassageWay Telephony
Manager. (The default application folder is PassageWay Telephony
Manager.)
 4. Select PassageWay Telephony Manager.
   If you have configured the Dialing Properties for your PC previously,
the Number of Calls dialog box appears the first time you start
Telephony Manager.
Figure...

Installing and Configuring Telephony
Manager
2-40
   If you have not configured the Dialing Properties for your PC
previously, a message box appears, prompting you to configure your
dialing locations. Choose the OK button. The Dialing Properties dialog
box appears. Perform Steps 3 to 9 in the next section “Configuring
the Dialing Information” to configure your dialing locations and then
perform the steps in this procedure.
 5. In the 
Number of telephone lines available box, enter the number of
call...

Installing and Configuring Telephony
Manager
2-41
  8.  Choose the OK button.
   If only one telephony provider is installed on your PC (that is, either
the PassageWay Service Provider or the Unimodem Service
Provider), the Telephony Manager window appears. Proceed to
“Configuring the Dialing Information,” later in this chapter.
   If both the PassageWay Service Provider and the Unimodem Service
Provider are installed and configured on your PC, a message box
appears, stating that you must select a...

Installing and Configuring Telephony
Manager
2-42
Configuring the Dialing
Information
This section describes how to configure the following dialing information:
„the digit(s) you must dial before you can make a local call (that is, an
external call)
„the digit(s) you must dial before you can make a long-distance call
„the area code for your telephone
To configure the dialing information:
  1.  From the View menu in the Telephony Manager window, choose
Dialing Properties.
   If you are using Windows NT,...

Installing and Configuring Telephony
Manager
2-43
Figure 2-14.  Sample Telephony Properties Dialog Box 

Installing and Configuring Telephony
Manager
2-44
  2.  If you are using Windows 95, choose the Dialing Properties button.
   The Dialing Properties dialog box appears.
Figure 2-15.  Sample Dialing Properties Dialog Box
 3. In the 
I am dialing from box, select Default Location.
 4. In 
The area code is box, enter the area code for your location.
 5. In the 
I am in box, select your country. 

Installing and Configuring Telephony
Manager
2-45
 6. In the First dial for local box, enter the digit(s) you must dial to access
an outside line for local calls (for example, “9”). Once you enter the
digit(s), you do not need to enter them when you make calls from
Telephony Manager. Telephony Manager inserts the digit(s)
automatically.
 7. In the 
First dial for long distance box, enter the digit(s) you must dial
to access an outside line for long-distance calls (for example, “9”).
Once you enter the...