Lucent Technologies PassageWay Telephony Manager R2.0 For PARTNER Communications System Getting Started Manual

Installing and Configuring the PassageWay
Service Provider
2-26
   The PassageWay Service Provider can recognize the following call
handling features programmed to your telephone:
¾ Auto Dial
¾ Call Forward
¾ Do Not Disturb
¾ Caller ID Inspect (Inspect)
  NOTE:
Features that cannot be programmed to buttons on your
telephone are disabled (that is, you cannot program these
features).
 g.  Choose the Continue button.
   The Configuration Complete message box appears.
  h.  Proceed to Step 35. 

Installing and Configuring the PassageWay
Service Provider
2-27
  23.  Choose the No button.
   The Extension Number dialog box appears.   
Figure 2-10.  Extension Number Dialog Box
  24.  Enter your extension number, and then choose the Continue button.
   If you specified that you have a standard telephone, the Enter
Number dialog box appears. Enter the telephone number for the
outside line, and then choose the OK button. The PassageWay
Configurator - Complete message box appears. Proceed to Step 34....

Installing and Configuring the PassageWay
Service Provider
2-28
Figure 2-11.  Sample Phone Line Information Dialog Box
   This dialog box presents a representation of the buttons on your
telephone. Using this dialog box, you will specify the location for each
outside line on your telephone. 

Installing and Configuring the PassageWay
Service Provider
2-29
  25.  Choose the location of an outside line on your telephone.
   A submenu appears, displaying the following options:
¾ Clear Button, which removes the programming (if any) and label (if
any) from the selected button.
¾ Outside Line, which enables you to specify the telephone number of
the outside line for the selected button.
¾ Cancel, which closes the submenu without changing the
programming for the selected button.
  
  NOTE:
   Make...

Installing and Configuring the PassageWay
Service Provider
2-30
  29.  When you are finished, choose the Continue button.
   The Feature Buttons dialog box appears.
Figure 2-12.  Sample Feature Buttons Dialog Box
   Using this dialog box, you specify the location of call handling
features assigned to buttons on your telephone by the PARTNER
System Manager. By specifying the locations of feature buttons,
telephony applications can use these call handling features to
enhance their operation. 

Installing and Configuring the PassageWay
Service Provider
2-31
   The PassageWay Service Provider can recognize the following call
handling features programmed to your telephone:
 ¾ Auto Dial
 ¾ Call Forward
 ¾ Do Not Disturb
 ¾ Caller ID Inspect (Inspect)
  NOTE:
„Features that cannot be programmed to buttons on your
telephone are disabled (that is, you cannot program these
features).
„Make sure you specify the correct type and location of each
feature assigned to buttons on your telephone. If you...

Installing and Configuring the PassageWay
Service Provider
2-32
  30.  Choose a button where a feature is assigned.
   A submenu appears, displaying the following options:
 ¾ Clear Button
 ¾ Auto Dial
 ¾ Call Forward
 ¾ Do Not Disturb
 ¾ Inspect
 ¾ Cancel
  31.  Choose the appropriate feature for the selected button.
   The label for the selected feature appears on the button.
  32.  Repeat Steps 30 and 31 for any other buttons.
  33.  When you are finished, choose the Continue button.
   The PassageWay...

Installing and Configuring the PassageWay
Service Provider
2-33
  37.  When you are finished reading the Readme file, select 
Exit from the
File menu to close the Notepad window.
  
  NOTE:
   If you have any other Notepad windows open, you must close
all of them now. The installation will not continue until all
Notepad windows are closed.
   The About To Restart Windows message box appears.
  38.  Choose the OK button.
   The Install dialog box appears.
  39.  Remove the diskette from the diskette drive...

Installing and Configuring Telephony
Manager
2-34
Installing the Telephony Manager
Software
This section describes how to install Telephony Manager.
To install Telephony Manager:
  1.  Start Windows (if it is not running already).
  2.  Shut down all applications running on your PC.
  3.  If you are installing from CD-ROM, insert the Telephony Manager
CD-ROM into the CD-ROM drive of your PC. If the Autorun feature is
enabled on your PC, the PassageWay Setup dialog box appears.
Proceed to Step 6.
   If...

Installing and Configuring Telephony
Manager
2-35
 ¾ If you are installing from diskette, double-click on the diskette drive
icon, and then double-click on setup.exe. The PassageWay
Telephony Manager Setup dialog box appears. Proceed to Step 7.
 6. Select the 
PassageWay Telephony Manager option button, and then
choose the OK button.
   The PassageWay Telephony Manager Setup dialog box appears.
  7.  Choose the Next button.
   The Select Destination Directory dialog box appears. This dialog box
displays...