Lucent Technologies PassageWay Telephony Manager R2.0 For PARTNER Communications System Getting Started Manual

Installing and Configuring the PassageWay
Service Provider
2-16
  8.  Choose the Next button.
   The Select Destination Directory dialog box appears. This dialog box
displays the name of the directory where the PassageWay Service
Provider software will be installed by default.
  9.  If the default directory is unacceptable, choose the Browse button
and specify an alternate directory. Otherwise, proceed to Step 10.
  10.  Choose the Next button.
   The Select Application Folder dialog box appears. This...

Installing and Configuring the PassageWay
Service Provider
2-17
  15.  Choose the Finish button.
   The PassageWay Configurator is launched, and it displays the Find
PassageWay Phone dialog box.
Figure 2-3.  Find PassageWay Link Dialog Box
   The PassageWay Configurator is a software application that enables
you to set up the PassageWay Service Provider. Until you set up the
PassageWay Service Provider, you will be unable to use any TAPI
applications.
   Setting up the PassageWay Service Provider...

Installing and Configuring the PassageWay
Service Provider
2-18
 ¾ the location and telephone number of each outside line button on
your telephone
 ¾ the location of feature buttons on your telephone
  NOTE:
The PassageWay Configurator does not verify whether the
information you enter is correct. When you run a TAPI application
(for example, Telephony Manager), the PassageWay Service
Provider tries to use the information you entered via the
PassageWay Configurator. If the information you entered in the...

Installing and Configuring the PassageWay
Service Provider
2-19
Figure 2-4.  Sample PassageWay Configurator - COM Port Dialog Box 

Installing and Configuring the PassageWay
Service Provider
2-20
  17.  Perform one of the following steps:
¾ If PassageWay “found” the COM port for you, choose the Continue
button.
¾ If PassageWay did not find the COM port for you, select the option
button of the COM port in your PC to which your PassageWay
adapter is connected, and then choose the Continue button.
   The PARTNER System Version dialog box appears.
Figure 2-5.  PARTNER System Version Dialog Box 

Installing and Configuring the PassageWay
Service Provider
2-21
  18.  From the PARTNER System Version dialog box, select the PARTNER
system you are using, and then choose the Continue button.
   The Telephone Models dialog box appears.
Figure 2-6.  Telephone Models Dialog Box
  19.  Select the telephone you are using.
  20.  If a secondary device (such as answering machine or a fax machine)
is attached your PARTNER system phone, choose the 
Secondary
Device
 check box. 

Installing and Configuring the PassageWay
Service Provider
2-22
  21.  Choose the Continue button.
   The Auto Configure Your Telephone dialog box appears.
Figure 2-7.  Auto Configure Your Telephone Dialog Box
   The PassageWay Configurator can automatically read the following
information from your telephone:
¾ the location of outside line buttons on your telephone
¾ the location of Auto Dial buttons, Call Forward buttons, Do Not
Disturb button, and Caller ID Inspect (Inspect) button programmed
on your...

Installing and Configuring the PassageWay
Service Provider
2-23
   If the PassageWay Configurator is unable to read the programming
from your telephone, an Error message box appears. Choose the
OK button. The Extension Number dialog box appears. Proceed to
Step 24.
   When the PassageWay Configurator is finished reading the
programming information from your telephone, the Phone Line
Information dialog box appears for the telephone type you specified.
Figure 2-8.  Sample Phone Line Information Dialog Box 

Installing and Configuring the PassageWay
Service Provider
2-24
   This dialog box shows the location of outside line buttons, Auto Dial
buttons, Call Forward buttons, Do Not Disturb button, and Caller ID
Inspect button programmed on your telephone.
   At this point, you must specify the telephone number for each
 button displayed in the Phone Line Information dialog
box.
 b.  Click on a  button.
   A submenu appears, displaying the following options:
¾ Clear Button, which removes the programming (if...

Installing and Configuring the PassageWay
Service Provider
2-25
Figure 2-9.  Sample Feature Buttons Dialog Box
   This dialog box shows the location of call handling features
assigned to buttons on your telephone by the PARTNER System
Manager. Telephony applications can use these call handling
features to enhance their operation.