Lucent Technologies PassageWay Telephony Manager R2.0 For PARTNER Communications System Getting Started Manual

							Installing and Configuring the PassageWay
Service Provider
2-16
  8.  Choose the Next button.
   The Select Destination Directory dialog box appears. This dialog box
displays the name of the directory where the PassageWay Service
Provider software will be installed by default.
  9.  If the default directory is unacceptable, choose the Browse button
and specify an alternate directory. Otherwise, proceed to Step 10.
  10.  Choose the Next button.
   The Select Application Folder dialog box appears. This dialog box
displays the name of the application folder to which the PassageWay
Service Provider icons will be added.
  11.  If the default application folder is unacceptable, enter the name of the
new folder to be created or select an existing folder. Otherwise,
proceed to Step 12.
  12.  Choose the Next button.
   The Ready to Install dialog box appears.
  13.  Choose the Next button.
   The installation program copies files to the destination directory. The
installation program displays a message box to inform you of its
status as it installs files.
   If you are installing from diskette, insert the requested PassageWay
Service Provider software diskette into the PC when prompted, and
choose the OK button.
   After the software is installed, the Creating Application Folder & Short
Cuts message box appears.
  14.  Choose the OK button.
   The Installation Completed message box appears. 
						

							Installing and Configuring the PassageWay
Service Provider
2-17
  15.  Choose the Finish button.
   The PassageWay Configurator is launched, and it displays the Find
PassageWay Phone dialog box.
Figure 2-3.  Find PassageWay Link Dialog Box
   The PassageWay Configurator is a software application that enables
you to set up the PassageWay Service Provider. Until you set up the
PassageWay Service Provider, you will be unable to use any TAPI
applications.
   Setting up the PassageWay Service Provider consists of specifying
the following information:
 ¾ the COM port to which the PassageWay adapter is connected
 ¾ the version and release of the PARTNER system your company has
(for example, PARTNER ACS R3.0)
 ¾ the type of telephone you have
 ¾ the extension number of your telephone 
						

							Installing and Configuring the PassageWay
Service Provider
2-18
 ¾ the location and telephone number of each outside line button on
your telephone
 ¾ the location of feature buttons on your telephone
  NOTE:
The PassageWay Configurator does not verify whether the
information you enter is correct. When you run a TAPI application
(for example, Telephony Manager), the PassageWay Service
Provider tries to use the information you entered via the
PassageWay Configurator. If the information you entered in the
PassageWay Configurator was correct, the TAPI application
works properly. If any of the information you entered is incorrect,
the TAPI application will not work. You must then run the
PassageWay Configurator and change the incorrect information.
   The Find PassageWay Link dialog box enables you to have the
PassageWay Configurator determine the COM port to which your
PassageWay adapter is connected.
  16.  Choose the Yes button.
   If the PassageWay Configurator found the COM port to which your
PassageWay adapter is connected, a message box appears, stating
that the PassageWay link was found and providing the number of the
COM port. Choose the OK button. The PassageWay Configurator -
COM Port dialog box appears, and the option button for the
corresponding COM port is selected.
   If the PassageWay Configurator did not find the COM port to which
your PassageWay adapter is connected, the PassageWay Link Not
Found message box appears. Choose the OK button. The
PassageWay Configurator - COM Port dialog box appears, and no
COM port option button is selected. 
						

							Installing and Configuring the PassageWay
Service Provider
2-19
Figure 2-4.  Sample PassageWay Configurator - COM Port Dialog Box 
						

							Installing and Configuring the PassageWay
Service Provider
2-20
  17.  Perform one of the following steps:
¾ If PassageWay “found” the COM port for you, choose the Continue
button.
¾ If PassageWay did not find the COM port for you, select the option
button of the COM port in your PC to which your PassageWay
adapter is connected, and then choose the Continue button.
   The PARTNER System Version dialog box appears.
Figure 2-5.  PARTNER System Version Dialog Box 
						

							Installing and Configuring the PassageWay
Service Provider
2-21
  18.  From the PARTNER System Version dialog box, select the PARTNER
system you are using, and then choose the Continue button.
   The Telephone Models dialog box appears.
Figure 2-6.  Telephone Models Dialog Box
  19.  Select the telephone you are using.
  20.  If a secondary device (such as answering machine or a fax machine)
is attached your PARTNER system phone, choose the 
Secondary
Device
 check box. 
						

							Installing and Configuring the PassageWay
Service Provider
2-22
  21.  Choose the Continue button.
   The Auto Configure Your Telephone dialog box appears.
Figure 2-7.  Auto Configure Your Telephone Dialog Box
   The PassageWay Configurator can automatically read the following
information from your telephone:
¾ the location of outside line buttons on your telephone
¾ the location of Auto Dial buttons, Call Forward buttons, Do Not
Disturb button, and Caller ID Inspect (Inspect) button programmed
on your telephone
  22.  Perform one of the following steps:
¾ If you want to manually configure the PassageWay Configurator,
proceed to Step 23.
¾ If you want to automatically configure the PassageWay Configurator,
perform the following steps:
  a.  Choose the Yes button.
   A message box appears showing the status of the PassageWay
Configurator reading the programming from your telephone. 
						

							Installing and Configuring the PassageWay
Service Provider
2-23
   If the PassageWay Configurator is unable to read the programming
from your telephone, an Error message box appears. Choose the
OK button. The Extension Number dialog box appears. Proceed to
Step 24.
   When the PassageWay Configurator is finished reading the
programming information from your telephone, the Phone Line
Information dialog box appears for the telephone type you specified.
Figure 2-8.  Sample Phone Line Information Dialog Box 
						

							Installing and Configuring the PassageWay
Service Provider
2-24
   This dialog box shows the location of outside line buttons, Auto Dial
buttons, Call Forward buttons, Do Not Disturb button, and Caller ID
Inspect button programmed on your telephone.
   At this point, you must specify the telephone number for each
 button displayed in the Phone Line Information dialog
box.
 b.  Click on a  button.
   A submenu appears, displaying the following options:
¾ Clear Button, which removes the programming (if any) and label
(if any) from the selected button.
¾ Outside Line, which enables you to specify the telephone number
of the outside line for the selected button.
¾ Cancel, which closes the submenu without changing the
programming for the selected button.
  c.  Choose Outside Line.
   The Enter Number dialog box appears.
 d.  Enter the telephone number for this outside line, and then choose
the OK button.
   The button displays LINE.
  e.  Repeat Steps b through d for any other  buttons on your
telephone.
  f.  When you are finished, choose the Continue button.
   The Feature Buttons dialog box appears. 
						

							Installing and Configuring the PassageWay
Service Provider
2-25
Figure 2-9.  Sample Feature Buttons Dialog Box
   This dialog box shows the location of call handling features
assigned to buttons on your telephone by the PARTNER System
Manager. Telephony applications can use these call handling
features to enhance their operation.