Lucent Technologies PassageWay Telephony Manager R2.0 For PARTNER Communications System Getting Started Manual

Installing and Configuring the PassageWay
Service Provider
2-6
„a system or standard telephone connected to a PARTNER system that
is configured and operating properly (if you want to use Telephony
Manager with a PARTNER system)
  NOTE:
A complete list of all the telephones supported by the
PassageWay Service Provider is provided in the PassageWay
Service Provider software (also known as the “PassageWay
Configurator”).
The PassageWay Service Provider operates with all versions of the
following PARTNER...

Installing and Configuring the PassageWay
Service Provider
2-7
  A PARTNER II Release 3.0 or later system will provide caller ID (if
available) for all outside lines connected to a 206EC module or a
400EC module.
 ¾ outside lines subscribed to caller ID from your local telephone
company.
 ¾ a system telephone that has a display and a Caller ID Inspect
button programmed. The Caller ID Inspect button is a display
feature button that shows you call-related information for an
incoming call when you are...

Installing and Configuring the PassageWay
Service Provider
2-8
Installing and Configuring the
PassageWay Service Provider
This section describes how to install and configure the PassageWay Service
Provider. You must perform the procedures in this section if you want to use
Telephony Manager with a PARTNER system. You should install the
PassageWay Service Provider before you install Telephony Manager.
The PassageWay Service Provider is a device driver that enables applications
that are compliant with the...

Installing and Configuring the PassageWay
Service Provider
2-9 Before You Begin
This section describes the information that is required to install and configure
the PassageWay Service Provider.
Before installing the PassageWay Service Provider, you also must know the
following information:
„the version and release of the PARTNER system your company has (for
example, PARTNER ACS R3.0)
„the type of telephone you have
„the extension number of your telephone
„the location and telephone number of each outside...

Installing and Configuring the PassageWay
Service Provider
2-10 Installing the PassageWay Adapter
This section describes how to connect the PassageWay adapter to your
telephone, your PC, and the line jack. The PassageWay adapter provides an
interface between the serial port on your PC and the Line jack on your
telephone, enabling you to access the PARTNER system from your PC. The
PassageWay adapter has a DB-25 connector for 25-pin serial ports. If you
have a 9-pin serial port on your PC, use the 9-pin to...

Installing and Configuring the PassageWay
Service Provider
2-11
PhoneLine
Line Cord
Figure 2-1.  Connecting the Line Cord to the PassageWay Adapter
  4.  Determine the type of serial port (9 pin or 25 pin) you have on your
PC. If you have a 9-pin serial port, you will use the 9-pin to 25-pin
adapter.
  5.  Connect the DB-25 connector on the PassageWay adapter to the
serial (COM) port on your PC. If your PC has a 9-pin serial (COM)
port, connect the 9-pin to 25-pin adapter to the 9-pin serial (COM)
port,...

Installing and Configuring the PassageWay
Service Provider
2-12
    NOTE:
   You can use an RS-232 cable to connect the adapter to the PC
if you do not want to connect the adapter directly to the PC.
  6.  Connect one end of the 7-foot, 2-pair, modular phone cord (D4BU) to
the jack labeled “Phone” on the PassageWay adapter (Figure 2-2).
PhoneLine
Modular Phone 
Cord (D4BU)
Figure 2-2.  Connecting the Modular Phone Cord to the PassageWay
Adapter 

Installing and Configuring the PassageWay
Service Provider
2-13
  7.  Connect the other end of the 7-foot, 2-pair, modular phone cord
(D4BU) to the Line jack on your telephone.
  8.  Check the LED on the PassageWay adapter. The LED is located next
to the Phone and Line jacks on the PassageWay adapter.
   If the red LED is “on,” proceed to Step 9.
   If the red LED is “off,” proceed to the section “PassageWay Adapter
LEDs” in Chapter 4.
  9.  Turn on your PC.
If you have an existing version of the...

Installing and Configuring the PassageWay
Service Provider
2-14 Installing the PassageWay Service Provider
Software
This section describes how to install and configure the PassageWay Service
Provider. You can modify the PassageWay Service Provider configuration
information later by running the PassageWay Configurator.
  NOTE:
If you have an earlier version of PassageWay Solution, you must exit
Connect or AT&TConnect (if it is running) before installing the new
PassageWay Service Provider.
To install the...

Installing and Configuring the PassageWay
Service Provider
2-15
  4.  If you are installing from CD-ROM, insert the Telephony Manager CD-
ROM into the CD-ROM drive of your PC. If the Autorun feature is
enabled on your PC, the PassageWay Setup dialog box appears.
Proceed to Step 7.
   If you are installing from a shared directory on a network server,
proceed to Step 5.
   If you are installing from diskette, insert PassageWay Service Provider
diskette #1 into the diskette drive of your PC. Proceed to Step...