Lucent Technologies DEFINITY Enterprise Communications Server Release 8.2 Instructions Manual

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
737 IP Trunk Configuration Manager 
17
Standard Command Buttons
The standard command buttons that you use as you work in Configuration 
Manager are:
nOK accepts your changes and exits Configuration Manager
nCancel cancels your changes and exits Configuration Manager
nApply accepts your changes and lets you continue working in 
Configuration Manager
nSet Default Values cancels your changes and resets the...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
738 IP Trunk Configuration Manager 
17
Viewing Information About the DEFINITY ECS 
Software
Use the Info property page to view information about the DEFINITY ECS 
software. You cannot change the information on this page. 
Telephony property page
Use the Telephony property page to:
nconfigure and monitor the connection between the switch and the IP trunk 
circuit pack.
ndisplay information about DSP...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
739 IP Trunk Configuration Manager 
17
PortsnPort Number: Allows you to specify the ports that you want to 
enable or disable by entering the port number, and selecting the 
Enable or Disable option button in the Status control group.
The maximum number of ports available is limited to the number 
of DEFINITY ECS licenses you purchased.
By default, all ports from 1 to the maximum number are set to an...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
740 IP Trunk Configuration Manager 
17
Telephony Advanced dialog box
Use the Telephony Advanced dialog box to adjust additional telephony 
parameters. 
The Telephony Advanced dialog box contains the following parameters:
Voice/Fax dialog box
Use the Voice/Fax property page to view information about, and configure some 
of the capabilities of, the DSP subsystem.
The Voice/Fax property page contains the...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
741 IP Trunk Configuration Manager 
17
VoicenGateway Voice Coder: Sets the type of voice coder used for voice 
calls. The voice coder type of both DEFINITY ECS systems 
should agree, or voice quality may be poor or calls may not 
connect.
nVoice Frames per Packet: Sets the number of frames of voice 
information sent in each packet when using the Gateway Voice 
Coder. 
Valid values: 
1 (packet) or 2....

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
742 IP Trunk Configuration Manager 
17
Internet dialog box
Use the Internet dialog box to configure your connection to an IP network. Adjust 
these parameters as needed for optimal performance.  Fax
nMaximum Fax Rate: Indicates the fax transmission rate. 
Valid values: 
9.6 Kpbs or 14.4 Kpbs.
nFax Error Control: Sets the level of redundant information used 
to improve the fax completion rate.
Valid values:...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
743 IP Trunk Configuration Manager 
17
The Internet dialog box contains the following parameters:
Parameter Description
Lucent Gateway 
ProtocolnSignaling Port: Displays the initial port number (5000) used for 
call setup. Display only.
nSetup Time-out (ms): Allows you to set the number of 
milliseconds to wait before canceling a call attempt while trying 
to set up the Internet connection.
If the call...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
744 IP Trunk Configuration Manager 
17
Dial/Routing Plan dialog box
The Dial/Routing Plan dialog box controls:
nhow the IP trunk application manipulates the digits it receives for outgoing 
and incoming calls
nthe IP addresses to which outgoing calls are routed
nthe remote sites that can access the DEFINITY ECS application on your 
switch
The Dial/Routing Plan dialog box contains the following parameters:...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
745 IP Trunk Configuration Manager 
17
Routing Info - 
Terminating Dial 
PlannEntry Type: Sets whether or not incoming calls are accepted. 
The default value is Accept. If you set this to Reject, then 
incoming calls are not accepted.
nSearch Digits: See the Dial/Routing Plan Worksheets.
nReplace Digits: See the Dial/Routing Plan Worksheets
nLine Number: In non-DCS configurations, enter Any. 
For DCS...

DEFINITY ECS Release 8.2
Administrator’s Guide  555-233-506  Issue 1.1
June 2000
Screen reference 
746 IP Trunk Configuration Manager 
17
Service Logs dialog box
Use the Service Logs dialog box to configure service logging options for the 
DEFINITY ECS application. 
The Service Logs dialog box contains the following parameters: Remove Allows you to remove the name of an DEFINITY ECS application 
connected to your network. Allows you to remove originating and 
terminating dial/routing plan information and...