Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-7 Digital Tie Trunk Example 
5
Digital Tie Trunk Example
This example shows how to connect digital tie trunk wiring from one DEFINITY 
System to another DEFINITY System. See Figure 5-6
.
Figure 5-6. Digital Tie Trunk Wiring
1. Install c ross-c onnec t jump ers to c onnec t the named  pins from the d igital 
trunk c irc uit pac k to ap p rop riate p...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-8 DS1 Tie Trunk Example 
5
The following cables can be used to connect DS1 tie trunk circuit packs to DS1 
digital facilities:
nC6C connector cable (comcode 104307327) — 50-foot (15.24 m) shielded 
cable equipped with a 50-pin male connector on 1 end and a 15-pin male 
connector on the other end. Use this cable to connect a DS1 tie trunk 
circuit...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-9 DS1 Tie Trunk Example 
5
Contact your Lucent Technologies representative for maximum cabling distances.
Figure 5-7. Typical Connections to Channel Service Unit Figure Notes
1. To TN722B DS1 Tie Trunk Circ uit 
Pa c k
2. C6C Cab le (For Distanc es Over 50 
Feet (15.24 m), Use C6E Cab les)
3. CSU or ICSU (3150 Shown)
4. T (Tip)5. R (Ring )
6. T1...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-10 Auxiliary Connector Outputs 
5
Auxiliary Connector Outputs
The control carrier output cable pinouts are shown in Table 5-2. The control carrier 
AUX connector outputs include the following: 
nAlarm monitoring for the auxiliary cabinet.
nSeven -48 VDC power sources for emergency transfer units.
nThree -48 VDC power sources for remotely powering 3...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-11 Auxiliary Connector Outputs 
5
BK-BL
BL-BK36
11-48
GNDEmerg ency
Tr an sf e r
Rel a y
Po w e r
¯ BK-O
O-BK37
12-48
GND
BK-G
G-BK38
13-48
GND
BK-BR
BR-BK39
14-48
GND
BK-S
S- BK40
15-48
GND
Y- B L
BL-Y41
16-48
GND
Y- O
O-Y42
17-48
GND
Y- G
G-Y43
18Not Connec ted
Y- BR
BR-Y44
19GND 
-48AUX Power 
Y- S
S- Y45
20GND 
-48
V- B L
BL-V46
21GND 
-48
V- O...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-12 Three-Pair and Four-Pair Modularity 
5
Table 5-3 provides port circuit pack and telephone pin designations.
Three-Pair and Four-Pair Modularity
Figure 5-8 shows 3-pair and 4-pair modularity from the por t circuit pack to the 
terminal pins at the information outlet (modular jack). Most terminals connect to 
an information outlet installed at the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-13 Adjunct Power Connections 
5
Make the connections from the port circuit pack to the modular jacks. Then, plug 
the terminal into the modular jack.
Figure 5-8. 3-Pair and 4-Pair Modularity
Adjunct Power Connections
Figure 5-9 shows 3 typical connection locations for adjunct power. Adjunct power 
for station equipment may be supplied from the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-14 Adjunct Power Connections 
5
Figure 5-9. Example Adjunct Power Connections
For Figure 5-9
, the following example is used:
a. If 25 telep hones c onnec t to the system and  all 25 telep hones need  
ad junc t p ower, install the ad junc t p ower sup p ly in the eq uip ment room.
b . If only 10 of the telep hones need ad junc t power, install the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-15 Adjunct Power Connections 
5
Local and Phantom Power
A console ’s maximum distance from the system is limited. See Ta b l e  5 - 4. 
Auxiliary Power
!CAUTION:
Do not use the 329A p ower unit for the attend ant c onsole.
The non-essential functions of an attendant console and its optional selector 
console derive their power from an auxiliary...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-16 Attendant Console 
5
Attendant Console
1. Install the attend ant c onsole and  c onnec t the mod ular c ord to the 
information outlet.
2. Install lab els p er the attend ant c onsole form and disp lay mod ule form 
assig nments.
3. Install a Digital Line c irc uit p ac k in the assig ned  c arrier slot (if an 
ad d itional c irc uit p ac k is...