Lucent Technologies DEFINITY Enterprise Communication Server Release 8.2 Installation And Test For Multi-Carrier Cabinets Manual

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-17 Connect External Alarm Indicators 
5
Connect External Alarm Indicators
Alarm Input
Alarms can be generated on adjunct equipment, sent to the DEFINITY System, 
and recorded and reported as “external alarms.” A typical major alarm 
input is 
from an Uninterruptible Power Supply (UPS).
1. Connec t 1 major and  1 minor alarm inp ut p air to the...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-18 Connect Power Distribution Unit External Alarm Wires 
5
Emergency Transfer and Auxiliary Power
Connect emergency transfer power and auxiliary power as shown in Ta b l e  5 - 7. 
Auxiliary power includes power to an attendant console or adjunct device.  
Connect Power Distribution Unit 
External Alarm Wires
The external alarm plug should already...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-19 Connect Power Distribution Unit External Alarm Wires 
5
7 Not Used
33 RFA2 + Rec tifier Failure (p ositive)
8 RFA2 - Rec tifier Failure (neg ative)
34 ACF2 + AC Failure (p ositive)
9 ACF2 - AC Failure (neg ative)
35 BIF2 + Battery Interfac e Failure (p ositive)
10 BIF2 - Battery Interfac e Failure (neg ative)
36 BOD2 + Battery On Disc harg e (p...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-20 Remote Network Interface 
5
NOTE:
RS-232 alarms (RXD, DTR, DSR, TXD, RS-232 GRD, and  RTS) are not 
sup p orted  on the BU3200A Battery Interfac e Unit.
1. Choose an alarm to c onnec t (suc h as Battery Interfac e Failure).
2. Choose the p ort c irc uit p ac k to use and  its c arrier and  slot numb er (from 
Tab le 5-3
). For example TN2183...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-21 TN1654 DS1 Converter (R8r Only) 
5
the TN1648 System Access/Maintenance (SYSAM) circuit pack through the 
remote network interface terminals at the trunk/auxiliary Main Distribution Frame 
(MDF). Figure 5-10
 shows a typical network interface trunk installation.
1. Determine the network interfac e trunk ap pearanc e at the g reen 
trunk/auxiliary...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-22 TN1654 DS1 Converter (R8r Only) 
5
Set Circuit Pack Switches
The configuration switches on the TN1654 must be set before the circuit pack is 
installed. The TN1654 can be configured for either T1 or E1 operation. All 4 
facilities on the circuit pack are configured as a group. It is not possible to have T1 
and E1 facilities supported on the same...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-23 TN1654 DS1 Converter (R8r Only) 
5
.
1. Set the c onfig uration switc hes on the TN1654 as req uired  p er site.
2. Set Switc h 6 d own (d isab led ). Switc h 6 may not b e p resent (or ac tive) on 
all TN1654 DS1 Converter c irc uit p ac ks.
3. Set Switc h 1 up for T1 fac ilities. All sub seq uent fac ility switc h setting s 
(Switc hes 2-5)...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-24 TN1654 DS1 Converter (R8r Only) 
5
Install the Circuit Pack and Cabling (T1 Only)
The following installation instructions are provided as examples only.
NOTE:
Be sure to lab el all of the c ab les as they are installed .
Port Carrier
1. Install the TN1654 c irc uit p ac k in any slot in a Port Carrier c lose to a 
TN570C Exp ansion Interfac e c...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-25 TN1654 DS1 Converter (R8r Only) 
5
Figure 5-12. DS1 Converter Connections — Part 1
Switch Node Carrier
You can install up to 2 TN1654 circuit packs in a Switch Node Carrier.
1. Install the TN1654 c irc uit p ac k in either slot 1 or 21 of the Switc h Nod e 
Carrier c lose to a TN573B SNI c irc uit pac k.
!CAUTION:
Install the TN1654 c irc uit p...

DEFINITY ECS Release 8.2 Installation and Test
for Multi-Carrier Cabinets  555-233-114  Issue 1
April 2000
Install and Wire Telephones and Other Equipment 
5-26 TN1654 DS1 Converter (R8r Only) 
5
!CAUTION:
The Y c ab le used  with the TN1654 c irc uit p ac k is d ifferent than the Y 
c ab le used with the TN574 c irc uit p ac k. These c ab les are NOT 
interc hangeab le.
3. Connec t an H600-348 Quad  c able to the other sid e of the Y c able.
4. Skip  to ‘‘
Channel Servic e Unit Cab ling’’.
Port Carrier...